Electrical Study guides, Study notes & Summaries

CWEA Electrical and Instrument Grade 2 Study Guide with Complete Solutions 2023

How DC motors operate? - correct answer -Magnetic lines of force are continuous and always form closed loops; Magnetic lines of force do not cross. Armature: (Definition) - correct answer -The rotating windings of a DC motor. The ____ is a movable electromagnet located between the poles of another fixed permanent (field) magnet as shown. - correct answer -Armature A twisting force called ______ must be developed. _____ is produced by mounting a loop in a fixed magnetic field and as long...

under strict safety guidelines, which of the following should be used to discharge capacitors before working on de-energized circuits. - safety shorting probe for safety, assume that any facility constructed before 1980 has? - asbestos with of the following is the threshold at which a power source is considered high voltage in the context of safety? - over 600V- 600Volts insulated gloves must be inspected by the user? - always and field checked the normal beating of a heart can be upset by...

Light energy that is NOT absorbed by an object can be _____. - correct answer -reflected from and/or transmitted through the object A light that is considered warm in tone is produced by lamps with color temperatures of _____. - correct answer -3,000°K The resistance of a tungsten filament is ______. - correct answer -much higher after the lamp is turned on The filament of a tungsten-halogen lamp is encased in a capsule containing iodine or _____. - correct answer -bromine gas Durin...

Electrical Level 3 Module 1 Load Calculations and Branch Feeder Circuits Quiz_ 2022. According to the NEC®, the ampacity of branch circuit conductors must be derated when there are more than how many current-carrying conductors in a raceway? Air conditioning overcurrent protective devices can never exceed what percentage of the motor-rated load current or the branch circuit selection current (whichever is greater)? Conductors must be derated when installed in conduit Continuous load...

The minimum bending radius for 3" rigid conduit is _____. - correct answer -13" The minimum bending radius for 1/2" rigid conduit is _____. - correct answer -4" The maximum number of 90° bends allowed between pull points in a conduit system is ______. - correct answer -four A saddle bend is counted as ____. - correct answer -60°-180°, depending on the type of bends When referring to the two bends required to make an offset in a length of conduit, which of the following is alwa...

According to the NEC®, the ampacity of branch circuit conductors must be derated when there are more than how many current-carrying conductors in a raceway? - correct answer 3 Air conditioning overcurrent protective devices can never exceed what percentage of the motor-rated load current or the branch circuit selection current (whichever is greater)? - correct answer 225% Conductors must be derated when installed in conduit - correct answer on or above rooftops Continuous loads are cal...

Which of the following is true regarding a series circuit? - correct answerThe current flow is the same through all resistors. Which of the following is true regarding a parallel circuit? - correct answerIt has more than one path for current to flow. Which of the following is true regarding a series-parallel circuit? - correct answerIf a circuit is reduced to an equivalent series circuit, the total resistance is found by adding the loads. Two branches of a circuit (R1 and R2) across a 1...

If the heater in a fixed IEC bimetallic overload relay fails, - correct answer -the entire overload relay must be replaced The nameplate of a motor indicates that the motor has an FLC of 15A and a service factor of 1.15, how much additional current can this motor safely handle for intermittent power demands? - correct answer -15A(1.15)= 17.25; 17.25A - 15A= 2.25A The minimum allowable coil control voltage needed to keep an electromechanical device energized is called the ___. - correct ans...

NOCTI Electrical Questions and Answers Already Passed In general a beginning tradesperson with little or no experience in the electrical field is known as a/an apprentice The proper angle for setting up a ladder is to place its base a/an___________ of the working length of the ladder from the wall or other vertical surface. quarter A __________ fire extinguisher should be used on an electrical fire. Class C A person with a serious electrical injury should be moved only if they are in immedia...