SACA Mech Drives 301 Exam Questions &
Answers Latest Update
Practice questions for this set
4
effort
Don't know?
Terms in this set (70)
What technique should be used when Keep back straight, bending knees, while lifting with legs
lifting heavy power transmission
components?
Which of the following is the coupling A rigid coupling
that would be used to combine two short
shafts to replace a long straight shaft?
Before removing a machine guard to fix a Lockout/Tagout the machine
machine, what step should a maintenance
technician perform?
, Which of the following is not one of the Make sure sprocket centers are at the same distance above the mounting plate
steps required to install an HTD belt?
Which of these conditions does NOT Top surface of the belt is worn
indicate that a V-belt drive sheave needs
to be replaced?
Which of the following is the primary To improve mechanical efficiency
function of a lubricant?
Thermal expansion causes the _______ of shaft height
a rotating component to change, which
affects alignment with other shafts.
In what way are grid couplings different Grid couplings allow for more misalignment because they are torsionally more
than chain coupling? flexible
Which type of shaft misalignment is Vertical angular
corrected first when performing a shaft
alignment procedure?
What component transmits power from a pulley
shaft to a timing belt?
Which of the following is an installation Force the belt onto the pulleys
procedure that will shorten the life of a
timing belt?
What method is used to find the nominal Measure the inside length of the belt
length of a conventional, or classic v
belt?
A v belt match code is used to: Identify belts to be used in a multi belt system
Which of the following is indicated if high belt is too tight
temperature is detected in a pillow block
bearing on a v belt drive?
When lubricating an unsealed pillow until old grease begins to flow out of the bearing
block bearing, the user attaches the
coupler into the grease fitting and slowly
pumps the handle of the grease gun
__________.
What problem can cause the chain to ride Too little tension
high on the teeth of a sprocket in a chain
drive?
What type of lubrication is commonly grease
used with a metal roller chain coupling?
Which of the following is the next step set the assembled width of the two sprockets
after performing alignment when
installing a chain coupling?
The purpose of the kiss idler in a belt reduce vibration or belt whipping
drive is to____ _.
A probable cause for chain wear and coupling misalignment
breakage in a chain type coupling is
__________.
The wedge V-belt ______ _. will carry the same load with 40% smaller cross section than a conventional V-belt
Chain pitch is important because it length
specifies both chain size and ____ _.
Which of the following is an advantage of It can be removed with a bearing puller
a QD bushing?
Answers Latest Update
Practice questions for this set
4
effort
Don't know?
Terms in this set (70)
What technique should be used when Keep back straight, bending knees, while lifting with legs
lifting heavy power transmission
components?
Which of the following is the coupling A rigid coupling
that would be used to combine two short
shafts to replace a long straight shaft?
Before removing a machine guard to fix a Lockout/Tagout the machine
machine, what step should a maintenance
technician perform?
, Which of the following is not one of the Make sure sprocket centers are at the same distance above the mounting plate
steps required to install an HTD belt?
Which of these conditions does NOT Top surface of the belt is worn
indicate that a V-belt drive sheave needs
to be replaced?
Which of the following is the primary To improve mechanical efficiency
function of a lubricant?
Thermal expansion causes the _______ of shaft height
a rotating component to change, which
affects alignment with other shafts.
In what way are grid couplings different Grid couplings allow for more misalignment because they are torsionally more
than chain coupling? flexible
Which type of shaft misalignment is Vertical angular
corrected first when performing a shaft
alignment procedure?
What component transmits power from a pulley
shaft to a timing belt?
Which of the following is an installation Force the belt onto the pulleys
procedure that will shorten the life of a
timing belt?
What method is used to find the nominal Measure the inside length of the belt
length of a conventional, or classic v
belt?
A v belt match code is used to: Identify belts to be used in a multi belt system
Which of the following is indicated if high belt is too tight
temperature is detected in a pillow block
bearing on a v belt drive?
When lubricating an unsealed pillow until old grease begins to flow out of the bearing
block bearing, the user attaches the
coupler into the grease fitting and slowly
pumps the handle of the grease gun
__________.
What problem can cause the chain to ride Too little tension
high on the teeth of a sprocket in a chain
drive?
What type of lubrication is commonly grease
used with a metal roller chain coupling?
Which of the following is the next step set the assembled width of the two sprockets
after performing alignment when
installing a chain coupling?
The purpose of the kiss idler in a belt reduce vibration or belt whipping
drive is to____ _.
A probable cause for chain wear and coupling misalignment
breakage in a chain type coupling is
__________.
The wedge V-belt ______ _. will carry the same load with 40% smaller cross section than a conventional V-belt
Chain pitch is important because it length
specifies both chain size and ____ _.
Which of the following is an advantage of It can be removed with a bearing puller
a QD bushing?
