MSSC EOC REVIEW EXAM WITH COMPLETE 380+
QUESTIONS AND ACCURATE VERIFIED
ANSWERS GRADED A+
Which HMI screen is often used to view real-time information
about system processes, such as line speed or barcode read rate?
-Correct Answer-Monitoring screen
The procedure performed to prepare a machine for its
production role is called what? -Correct Answer-Machine setup
Using proper production operation procedures will __________.
-Correct Answer-Help eliminate machine failures
__________ is the ability of a system or device to produce the
same outcome in unchanged conditions. -Correct Answer-
Repeatability
__________ must be set up properly to ensure that process
requirements and product specifications are met. -Correct
Answer-Production equipment
True or false: Filters are commonly combined with pressure
regulators. -Correct Answer-True
Which direction should a pressure regulator knob be turned in
order to increase pressure? -Correct Answer-Clockwise
,What is used to soften the impact of a rotary actuator's internal
cylinder against hard stops? -Correct Answer-Adjustable
cushion
Which of the following provides limited adjustment of a linear
actuator's stroke? -Correct Answer-Threaded rod and head
What type of transistor supplies voltage when activated, causing
the signal from the sensor to turn on? -Correct Answer-PNP
When adjusting the position of a limit switch, what should be
done before manually moving the actuator to the desired
position? -Correct Answer-Disable the machine outputs
When adjusting actuator speed with a flow control valve, which
direction should you turn the valve's knob to decrease speed? -
Correct Answer-Clockwise
What must be loosened before turning the flow control valve
knob to adjust actuator speed? -Correct Answer-Locking nut
Which of the following is NOT a common sensor mounting
method? -Correct Answer-Threaded rod and head-mounted
When should thread-locking fluid be applied to a fastener? -
Correct Answer-Before installation
Machine lubrication leaks can drip onto the floor and create a
hazardous condition for employees or cause damage to the
product. Therefore, if a leak occurs, __________. -Correct
,Answer-Notify the appropriate personnel to have the leak
repaired immediately
The safety of personnel and equipment performance are the key
points to keep in mind when making a decision to __________. -
Correct Answer-Run to failure or shut down the machine
Troubleshooting a machine problem is determining the cause
and __________. -Correct Answer-Taking the steps needed to
solve the problem
To calculate the time charged per machine, a work order must be
filled out with what data? -Correct Answer-Time entries
For example, many plants use an announcement system called
__________ (Japanese for signboard) to announce the need for
reactive maintenance. -Correct Answer-Andon
A(n) __________ must be initiated by one human action and
must override all other machine functions and operating modes.
-Correct Answer-Emergency stop
The Manufacturer's serial number and model of a machine are
used to identify the __________. -Correct Answer-Proper
service or parts manuals
An equipment manufacturer __________. -Correct Answer-Is
the best source of technical information on a specific piece of
equipment
, The __________ on a boiler burner makes it easy to detect a
main flame. -Correct Answer-UV fire eye
A thorough check for a history of similar problems should occur
__________. -Correct Answer-On problems that keep recurring
at regular intervals
A human-machine interface or HMI panel is where most
__________ are displayed. -Correct Answer-Machine alarms or
error messages
A critical system component is defined as what? -Correct
Answer-A component essential for continued system operation
The maintenance logs should be updated after fixing a
production problem so that __________. -Correct Answer-A
history of the problem can be recorded in case it occurs again
Production efficiency is the standard produced parts divided by
the actual produced parts. How is the standard determined? -
Correct Answer-The standard is the calculated amount produced
under ideal conditions
An important statistic is calculated by dividing the number of
parts produced by the number of hours worked. This statistic is
called __________. -Correct Answer-Labor productivity
Productivity can be calculated by __________ the number of
parts produced by the time elapsed during the production. -
Correct Answer-Dividing
QUESTIONS AND ACCURATE VERIFIED
ANSWERS GRADED A+
Which HMI screen is often used to view real-time information
about system processes, such as line speed or barcode read rate?
-Correct Answer-Monitoring screen
The procedure performed to prepare a machine for its
production role is called what? -Correct Answer-Machine setup
Using proper production operation procedures will __________.
-Correct Answer-Help eliminate machine failures
__________ is the ability of a system or device to produce the
same outcome in unchanged conditions. -Correct Answer-
Repeatability
__________ must be set up properly to ensure that process
requirements and product specifications are met. -Correct
Answer-Production equipment
True or false: Filters are commonly combined with pressure
regulators. -Correct Answer-True
Which direction should a pressure regulator knob be turned in
order to increase pressure? -Correct Answer-Clockwise
,What is used to soften the impact of a rotary actuator's internal
cylinder against hard stops? -Correct Answer-Adjustable
cushion
Which of the following provides limited adjustment of a linear
actuator's stroke? -Correct Answer-Threaded rod and head
What type of transistor supplies voltage when activated, causing
the signal from the sensor to turn on? -Correct Answer-PNP
When adjusting the position of a limit switch, what should be
done before manually moving the actuator to the desired
position? -Correct Answer-Disable the machine outputs
When adjusting actuator speed with a flow control valve, which
direction should you turn the valve's knob to decrease speed? -
Correct Answer-Clockwise
What must be loosened before turning the flow control valve
knob to adjust actuator speed? -Correct Answer-Locking nut
Which of the following is NOT a common sensor mounting
method? -Correct Answer-Threaded rod and head-mounted
When should thread-locking fluid be applied to a fastener? -
Correct Answer-Before installation
Machine lubrication leaks can drip onto the floor and create a
hazardous condition for employees or cause damage to the
product. Therefore, if a leak occurs, __________. -Correct
,Answer-Notify the appropriate personnel to have the leak
repaired immediately
The safety of personnel and equipment performance are the key
points to keep in mind when making a decision to __________. -
Correct Answer-Run to failure or shut down the machine
Troubleshooting a machine problem is determining the cause
and __________. -Correct Answer-Taking the steps needed to
solve the problem
To calculate the time charged per machine, a work order must be
filled out with what data? -Correct Answer-Time entries
For example, many plants use an announcement system called
__________ (Japanese for signboard) to announce the need for
reactive maintenance. -Correct Answer-Andon
A(n) __________ must be initiated by one human action and
must override all other machine functions and operating modes.
-Correct Answer-Emergency stop
The Manufacturer's serial number and model of a machine are
used to identify the __________. -Correct Answer-Proper
service or parts manuals
An equipment manufacturer __________. -Correct Answer-Is
the best source of technical information on a specific piece of
equipment
, The __________ on a boiler burner makes it easy to detect a
main flame. -Correct Answer-UV fire eye
A thorough check for a history of similar problems should occur
__________. -Correct Answer-On problems that keep recurring
at regular intervals
A human-machine interface or HMI panel is where most
__________ are displayed. -Correct Answer-Machine alarms or
error messages
A critical system component is defined as what? -Correct
Answer-A component essential for continued system operation
The maintenance logs should be updated after fixing a
production problem so that __________. -Correct Answer-A
history of the problem can be recorded in case it occurs again
Production efficiency is the standard produced parts divided by
the actual produced parts. How is the standard determined? -
Correct Answer-The standard is the calculated amount produced
under ideal conditions
An important statistic is calculated by dividing the number of
parts produced by the number of hours worked. This statistic is
called __________. -Correct Answer-Labor productivity
Productivity can be calculated by __________ the number of
parts produced by the time elapsed during the production. -
Correct Answer-Dividing
