Testout Network Pro Exam Questions &
Answers 100% Accurate!!
You manage a network with a single switch. On each switch port, a hub connects
multiple devices to the switch.
which condition are you most likely to experience on the network ? -
ANSWERScollisions
select the statement that best describes a broadcast storm. - ANSWERSA Broadcast
storm occurs when there are so many broadcast messages on the network that they
approach or exceed the network bandwidth..
Which of the following solutions would you implement to eliminate switching loops? -
ANSWERSspanning tree
You manage a network that uses a single switch. All ports within your buildings connect
through he single switch . Which feature should you implement? - ANSWERSVLANs
You manage a network that uses multiple switches. You want to provide multiple paths
between switches so that if one link goes down, an alternate path is available.
Which feature should your switch support? - ANSWERSspanning tree
You run a small network for your business that has a single router connected to the
internet and a single switch. You keep sensitive doc.
What should you use for this situation? - ANSWERSVLAN
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature prevents switching loops and ensures there is only a single active patch
between any two switches? - ANSWERSSpanning tree
Which feature prevents switching loops and ensures there is only a single active path
between any two switches? - ANSWERSspanning trees
A user reports that network access from her workstation is very slow. The problem does
not seem to be affecting any other users.
Which of the following conditions is the most likely cause? - ANSWERSDuplex
mismatch
You manage a local area network with several switches. A new employee has started
today so you connect her workstation to a switch port.
,Which of the following is the most likely cause of the problem? - ANSWERSIncorrect
VLAN assignment
You manage a network with multiple switches. You find that your switches are
experiencing heavy broadcast storms.
Which of the following will help reduce the effects of a broadcast storm? -
ANSWERSEnable spanning tree on the switches
Which of the following solutions would you implement to eliminate switching loops? -
ANSWERSspanning tree
While viewing the status of the interfaces on a Cisco switch, you see abnormally large
of oversized ethernet frames being received on one interface. This interface is
connected to a workstation located on the 2nd floor.
What could be causing this to happen? - ANSWERSThe workstation's network board is
jabbering
The network board in a workstation is currently configured as follows: - ANSWERSshow
running-config interface
show interface
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature allows the switches to pass VLAN traffic between the switches? -
ANSWERSTrunking
You manage a network with two switches. The switches are connected together through
their Gigabit Ethernet uplink ports.
You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1
needs to communicate with a device on the second switch also in VLAN 1.
What should you configure to allow communication between these two devices through
the switches? - ANSWERSTrunking
When configuring VLANs on a switch, what type of switch ports are members of all
VLANs defined on the switch? - ANSWERSTrunk Ports
Computers A and B are on the same VLAN and are separated by two switches, as
shown in the exhibit. Computer A sends a Fram to Computer B.
Which of the following best describes the composition of the frame as it travels from A
to B? - ANSWERSComputer A sends a normal frame. The first switch appends a VLAN
ID to the frame. The second switch removes the VLAN ID before forwarding it to
Computer B.
, Which of the following statements accurately describes a VLAN ID? -
ANSWERSSwitches append a VLAN ID to the header of each frame to identify the
virtual network to which it belongs.
CSMA/CD - ANSWERSThe media access control method of all Ethernet networks is
___________________.
The device listens to determine if the transmission media is free. - ANSWERSA network
is connected following the IEEE 802.3 specifications. Which of the following best
describes when a device can transmit messages?
10BaseT & 1000BaseT - ANSWERSWhich of the following use the CSMA/CD access
method? Select all that apply.
Bus and Star - ANSWERSWhich of the following physical topologies are used with
Ethernet networks? (Select two.)
Fiber optic - ANSWERSEthernet 100BaseFX networks use what type of cabling?
100BaseFX & 1000BaseLX - ANSWERSWhich of the following Ethernet standards uses
fiber optic cabling? (Select two.)
100 meters - ANSWERSYour network follows the 100BaseTx specifications for Fast
Ethernet. What is the maximum cable segment length allowed?
100 meters - ANSWERSWith an Ethernet 10BaseT network, the maximum cable length
between a computer and the hub is __________.
10BaseSR &1000BaseSX - ANSWERSYou have been tasked with designing an
Ethernet network. Your client needs to implement a very high-speed network backbone
between campus buildings; some of which are around 300 meters apart. Multimode
fiber-optic cabling has already been installed between buildings. Your client has asked
that you use the existing cabling.
Which Ethernet standard meets these guidelines? (Choose two.)
Type 1A STP or Category 5 UTP - ANSWERSWhat type of cabling is used with
100BaseTX Fast Ethernet networks?
Physical star/logical bus & Physical star/logical star - ANSWERSWhat topology is used
with 100BaseTX Fast Ethernet networks? (Select two.)
CAT 5 cabling & RJ-45 connectors & The cable length must be less than or equal to
100m - ANSWERSWhich of the following are requirements of the 1000BaseT Ethernet
standards? (Select three.)
Answers 100% Accurate!!
You manage a network with a single switch. On each switch port, a hub connects
multiple devices to the switch.
which condition are you most likely to experience on the network ? -
ANSWERScollisions
select the statement that best describes a broadcast storm. - ANSWERSA Broadcast
storm occurs when there are so many broadcast messages on the network that they
approach or exceed the network bandwidth..
Which of the following solutions would you implement to eliminate switching loops? -
ANSWERSspanning tree
You manage a network that uses a single switch. All ports within your buildings connect
through he single switch . Which feature should you implement? - ANSWERSVLANs
You manage a network that uses multiple switches. You want to provide multiple paths
between switches so that if one link goes down, an alternate path is available.
Which feature should your switch support? - ANSWERSspanning tree
You run a small network for your business that has a single router connected to the
internet and a single switch. You keep sensitive doc.
What should you use for this situation? - ANSWERSVLAN
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature prevents switching loops and ensures there is only a single active patch
between any two switches? - ANSWERSSpanning tree
Which feature prevents switching loops and ensures there is only a single active path
between any two switches? - ANSWERSspanning trees
A user reports that network access from her workstation is very slow. The problem does
not seem to be affecting any other users.
Which of the following conditions is the most likely cause? - ANSWERSDuplex
mismatch
You manage a local area network with several switches. A new employee has started
today so you connect her workstation to a switch port.
,Which of the following is the most likely cause of the problem? - ANSWERSIncorrect
VLAN assignment
You manage a network with multiple switches. You find that your switches are
experiencing heavy broadcast storms.
Which of the following will help reduce the effects of a broadcast storm? -
ANSWERSEnable spanning tree on the switches
Which of the following solutions would you implement to eliminate switching loops? -
ANSWERSspanning tree
While viewing the status of the interfaces on a Cisco switch, you see abnormally large
of oversized ethernet frames being received on one interface. This interface is
connected to a workstation located on the 2nd floor.
What could be causing this to happen? - ANSWERSThe workstation's network board is
jabbering
The network board in a workstation is currently configured as follows: - ANSWERSshow
running-config interface
show interface
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature allows the switches to pass VLAN traffic between the switches? -
ANSWERSTrunking
You manage a network with two switches. The switches are connected together through
their Gigabit Ethernet uplink ports.
You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1
needs to communicate with a device on the second switch also in VLAN 1.
What should you configure to allow communication between these two devices through
the switches? - ANSWERSTrunking
When configuring VLANs on a switch, what type of switch ports are members of all
VLANs defined on the switch? - ANSWERSTrunk Ports
Computers A and B are on the same VLAN and are separated by two switches, as
shown in the exhibit. Computer A sends a Fram to Computer B.
Which of the following best describes the composition of the frame as it travels from A
to B? - ANSWERSComputer A sends a normal frame. The first switch appends a VLAN
ID to the frame. The second switch removes the VLAN ID before forwarding it to
Computer B.
, Which of the following statements accurately describes a VLAN ID? -
ANSWERSSwitches append a VLAN ID to the header of each frame to identify the
virtual network to which it belongs.
CSMA/CD - ANSWERSThe media access control method of all Ethernet networks is
___________________.
The device listens to determine if the transmission media is free. - ANSWERSA network
is connected following the IEEE 802.3 specifications. Which of the following best
describes when a device can transmit messages?
10BaseT & 1000BaseT - ANSWERSWhich of the following use the CSMA/CD access
method? Select all that apply.
Bus and Star - ANSWERSWhich of the following physical topologies are used with
Ethernet networks? (Select two.)
Fiber optic - ANSWERSEthernet 100BaseFX networks use what type of cabling?
100BaseFX & 1000BaseLX - ANSWERSWhich of the following Ethernet standards uses
fiber optic cabling? (Select two.)
100 meters - ANSWERSYour network follows the 100BaseTx specifications for Fast
Ethernet. What is the maximum cable segment length allowed?
100 meters - ANSWERSWith an Ethernet 10BaseT network, the maximum cable length
between a computer and the hub is __________.
10BaseSR &1000BaseSX - ANSWERSYou have been tasked with designing an
Ethernet network. Your client needs to implement a very high-speed network backbone
between campus buildings; some of which are around 300 meters apart. Multimode
fiber-optic cabling has already been installed between buildings. Your client has asked
that you use the existing cabling.
Which Ethernet standard meets these guidelines? (Choose two.)
Type 1A STP or Category 5 UTP - ANSWERSWhat type of cabling is used with
100BaseTX Fast Ethernet networks?
Physical star/logical bus & Physical star/logical star - ANSWERSWhat topology is used
with 100BaseTX Fast Ethernet networks? (Select two.)
CAT 5 cabling & RJ-45 connectors & The cable length must be less than or equal to
100m - ANSWERSWhich of the following are requirements of the 1000BaseT Ethernet
standards? (Select three.)
