310T Practice Exam 2 – Questions With Verified
Solutions
Save Groups
Terms in this set (136)
Which of the following tools can be A die
used to cut new external threads?!
A die
A thread pitch gauge
A tap
A thread chaser
During a PM inspection a broken A broken engine mount
radiator fan shroud is noticed. Which
of the following could cause this
damage?!
Loose fan belts
A failed fan hub clutch
A broken engine mount
An out of balance fan assembly
During a PM inspection the steering Worn steering shaft universal joints
wheel binds when turned. What could
cause this condition?!
Excessive sector gear to ball nut
clearance in the steering gear
Worn king pin bushings
Worn steering shaft universal joints
Worn tie rod ends
,Although any loose or missing bolts 20%
should be tightened or replaced when
noticed, what percentage of fifth
wheel mounting bracket to frame
fasteners can be loose or missing
before the tractor must be placed out
of service?!
10%
20%
30%
40%
What type of tubing must be used in Double wall thickness steel tubing
hydraulic brake systems?!
Single wall thickness steel tubing
Double wall thickness steel tubing
Single wall thickness copper tubing
Double wall thickness copper tubing
When cutting with an oxy-acetylene A small liquid puddle
torch, what should you see in the steel
before depressing the cutting lever?!
A small liquid puddle
A change in steel colour
A change in steel colour to red
A change in flame colour to red
What is the reading on this 2-3" 2.341"
imperial micrometer?!
2.341"
2.016"
2.516"
2.041"
What tool should be used to measure A water manometer
the air filter restriction?!
A water manometer
A vacuum gauge
A mercury manometer
A pressure gauge
,When lengthening a truck frame, at 60 degrees to the frame centreline
what angle should the frame be cut?!
30 degrees to the frame centreline
60 degrees to the frame centreline
90 degrees to the frame centreline
120 degrees to the frame centreline
When a truck has been involved in an Diamond damage
offset front end collision, what type of
frame damage would be expected?!
Diamond damage
Twist damage
Sideway damage
Sag and bow damage
When installing a reinforcement plate In a staggered bolt pattern
on a truck frame, how should the bolt
holes be located?!
In a vertical row
In a staggered bolt pattern
Close to the upper frame flange
Along each edge of the plate
What should be used to lubricate the Mixture of light oil and diesel fuel
rack and slide path of a sliding fifth
wheel?!
All purpose grease
SAE 30 engine oil
Water resistant lithium based grease
Mixture of light oil and diesel fuel
When will the ride height control When more load is applied to the truck
valve supply more air to the air
springs?!
When more load is applied to the
truck
When less load is applied to the truck
When uneven terrain is encountered
When the compressor begins its
loaded cycle
, What must be performed on a truck Remove or add washers (shims)
suspension system to adjust torque
rod length and drive axle alignment?!
Adjust the nuts on the U-bolts
Add additional spring wedges
Remove or add washers (shims)
Adjust the position of the spring
hangers
What type of truck spring suspension An auxiliary spring suspension
system would be mounted above the
main leaf spring assembly and only be
utilized under heavy leads?!
An air spring suspension
A constant spring suspension
An auxiliary spring suspension
A coil spring suspension
What component is used to control A shock absorber
jounce and rebound and suppress
truck suspension system oscillations?!
An air spring
A shock absorber
A leaf spring
A helper spring
When diagnosing a leaf spring Seized front spring shackle pins
suspension complaint of harsh ride
which of the following could be the
cause?!
Seized front spring shackle pins
Tires under-inflated
Broken leaf spring
Inadequate fifth-wheel lubrication
Solutions
Save Groups
Terms in this set (136)
Which of the following tools can be A die
used to cut new external threads?!
A die
A thread pitch gauge
A tap
A thread chaser
During a PM inspection a broken A broken engine mount
radiator fan shroud is noticed. Which
of the following could cause this
damage?!
Loose fan belts
A failed fan hub clutch
A broken engine mount
An out of balance fan assembly
During a PM inspection the steering Worn steering shaft universal joints
wheel binds when turned. What could
cause this condition?!
Excessive sector gear to ball nut
clearance in the steering gear
Worn king pin bushings
Worn steering shaft universal joints
Worn tie rod ends
,Although any loose or missing bolts 20%
should be tightened or replaced when
noticed, what percentage of fifth
wheel mounting bracket to frame
fasteners can be loose or missing
before the tractor must be placed out
of service?!
10%
20%
30%
40%
What type of tubing must be used in Double wall thickness steel tubing
hydraulic brake systems?!
Single wall thickness steel tubing
Double wall thickness steel tubing
Single wall thickness copper tubing
Double wall thickness copper tubing
When cutting with an oxy-acetylene A small liquid puddle
torch, what should you see in the steel
before depressing the cutting lever?!
A small liquid puddle
A change in steel colour
A change in steel colour to red
A change in flame colour to red
What is the reading on this 2-3" 2.341"
imperial micrometer?!
2.341"
2.016"
2.516"
2.041"
What tool should be used to measure A water manometer
the air filter restriction?!
A water manometer
A vacuum gauge
A mercury manometer
A pressure gauge
,When lengthening a truck frame, at 60 degrees to the frame centreline
what angle should the frame be cut?!
30 degrees to the frame centreline
60 degrees to the frame centreline
90 degrees to the frame centreline
120 degrees to the frame centreline
When a truck has been involved in an Diamond damage
offset front end collision, what type of
frame damage would be expected?!
Diamond damage
Twist damage
Sideway damage
Sag and bow damage
When installing a reinforcement plate In a staggered bolt pattern
on a truck frame, how should the bolt
holes be located?!
In a vertical row
In a staggered bolt pattern
Close to the upper frame flange
Along each edge of the plate
What should be used to lubricate the Mixture of light oil and diesel fuel
rack and slide path of a sliding fifth
wheel?!
All purpose grease
SAE 30 engine oil
Water resistant lithium based grease
Mixture of light oil and diesel fuel
When will the ride height control When more load is applied to the truck
valve supply more air to the air
springs?!
When more load is applied to the
truck
When less load is applied to the truck
When uneven terrain is encountered
When the compressor begins its
loaded cycle
, What must be performed on a truck Remove or add washers (shims)
suspension system to adjust torque
rod length and drive axle alignment?!
Adjust the nuts on the U-bolts
Add additional spring wedges
Remove or add washers (shims)
Adjust the position of the spring
hangers
What type of truck spring suspension An auxiliary spring suspension
system would be mounted above the
main leaf spring assembly and only be
utilized under heavy leads?!
An air spring suspension
A constant spring suspension
An auxiliary spring suspension
A coil spring suspension
What component is used to control A shock absorber
jounce and rebound and suppress
truck suspension system oscillations?!
An air spring
A shock absorber
A leaf spring
A helper spring
When diagnosing a leaf spring Seized front spring shackle pins
suspension complaint of harsh ride
which of the following could be the
cause?!
Seized front spring shackle pins
Tires under-inflated
Broken leaf spring
Inadequate fifth-wheel lubrication
