Millwright Alberta Period 1 Final Exam PREPARATION
MILLWRIGHT ALBERTA PERIOD 1 FINAL EXAM PREPARATION NEWEST
2025/2026 WITH COMPLETE QUESTIONS AND CORRECT DETAILED
ANSWERS| BRAND NEW VERSION!
What is used with an outside caliper to measure a shaft?
a) Micrometer
b) Steel rule
c) Vernier caliper
d) Dial indicator
e) Depth gauge
Correct answer: b) Steel rule
What is the smallest measurement of a vernier caliper?
a) 0.02 mm
b) 1/64 in
c) 0.01 mm
d) 0.001 in (0.001") or 0.02 mm
e) 0.20 mm
Correct answer: d) 0.001 in (0.001") or 0.20 mm
Parallel misalignment plus angular misalignment is called?
a) Radial misalignment
b) Offset misalignment
c) Compound misalignment
d) Combination misalignment
e) Axial misalignment
Correct answer: d) Combination misalignment
1|Page
, Millwright Alberta Period 1 Final Exam PREPARATION
How do you measure a small hole accurately?
a) Inside micrometer
b) Telescoping gauge and caliper
c) Small hole gauge and outside micrometer
d) Depth micrometer
e) Plug gauge
Correct answer: c) Small hole gauge and outside micrometer
A vernier bevel protractor is read in which units?
a) Degrees only
b) Degrees and seconds
c) Radians
d) Degrees on main scale and minutes on vernier scale
e) Inches per foot
Correct answer: d) Degrees on main scale and minutes on vernier scale
What must be aligned during machine installation?
a) Bearings
b) Mounting bolts
c) Centerlines
d) Guards
e) Base plates
Correct answer: c) Centerlines
What is a datum line?
2|Page
, Millwright Alberta Period 1 Final Exam PREPARATION
a) A finished edge
b) A temporary reference mark
c) A standard of comparison or point of reference
d) A center punch mark
e) A layout chalk line
Correct answer: c) A standard of comparison or point of reference
The most important point prior to starting a layout is establishing the?
a) Finished surface
b) Center punch
c) Measurement tolerance
d) Reference line (datum line)
e) Tool alignment
Correct answer: d) Reference line (datum line)
Smallest dimension on a steel rule is typically?
a) 1/32
b) 1/100
c) 1/16
d) 1/64
e) 0.5 mm
Correct answer: d) 1/64
Accuracy of a vernier caliper is?
a) 0.1 mm
b) 0.02 mm
c) 0.01 mm or 0.001"
3|Page
, Millwright Alberta Period 1 Final Exam PREPARATION
d) 1/64 in
e) 0.05 mm
Correct answer: c) 0.01 mm or 0.001"
What tool is used to set the threading tool at a right angle to the workpiece axis?
a) Dial indicator
b) Tool height gauge
c) Combination square
d) Thread centre gauge (fishtail)
e) Bevel protractor
Correct answer: d) Thread centre gauge (fishtail)
Sensitive tool used to measure the depth of small holes and bores?
a) Vernier depth gauge
b) Dial depth gauge
c) Depth micrometer
d) Inside micrometer
e) Steel rule
Correct answer: c) Depth micrometer
Most effective type of hearing protection?
a) Earplugs only
b) Earmuffs only
c) Noise-cancelling headphones
d) Plugs and earmuffs
e) Cotton inserts
Correct answer: d) Plugs and earmuffs
4|Page
MILLWRIGHT ALBERTA PERIOD 1 FINAL EXAM PREPARATION NEWEST
2025/2026 WITH COMPLETE QUESTIONS AND CORRECT DETAILED
ANSWERS| BRAND NEW VERSION!
What is used with an outside caliper to measure a shaft?
a) Micrometer
b) Steel rule
c) Vernier caliper
d) Dial indicator
e) Depth gauge
Correct answer: b) Steel rule
What is the smallest measurement of a vernier caliper?
a) 0.02 mm
b) 1/64 in
c) 0.01 mm
d) 0.001 in (0.001") or 0.02 mm
e) 0.20 mm
Correct answer: d) 0.001 in (0.001") or 0.20 mm
Parallel misalignment plus angular misalignment is called?
a) Radial misalignment
b) Offset misalignment
c) Compound misalignment
d) Combination misalignment
e) Axial misalignment
Correct answer: d) Combination misalignment
1|Page
, Millwright Alberta Period 1 Final Exam PREPARATION
How do you measure a small hole accurately?
a) Inside micrometer
b) Telescoping gauge and caliper
c) Small hole gauge and outside micrometer
d) Depth micrometer
e) Plug gauge
Correct answer: c) Small hole gauge and outside micrometer
A vernier bevel protractor is read in which units?
a) Degrees only
b) Degrees and seconds
c) Radians
d) Degrees on main scale and minutes on vernier scale
e) Inches per foot
Correct answer: d) Degrees on main scale and minutes on vernier scale
What must be aligned during machine installation?
a) Bearings
b) Mounting bolts
c) Centerlines
d) Guards
e) Base plates
Correct answer: c) Centerlines
What is a datum line?
2|Page
, Millwright Alberta Period 1 Final Exam PREPARATION
a) A finished edge
b) A temporary reference mark
c) A standard of comparison or point of reference
d) A center punch mark
e) A layout chalk line
Correct answer: c) A standard of comparison or point of reference
The most important point prior to starting a layout is establishing the?
a) Finished surface
b) Center punch
c) Measurement tolerance
d) Reference line (datum line)
e) Tool alignment
Correct answer: d) Reference line (datum line)
Smallest dimension on a steel rule is typically?
a) 1/32
b) 1/100
c) 1/16
d) 1/64
e) 0.5 mm
Correct answer: d) 1/64
Accuracy of a vernier caliper is?
a) 0.1 mm
b) 0.02 mm
c) 0.01 mm or 0.001"
3|Page
, Millwright Alberta Period 1 Final Exam PREPARATION
d) 1/64 in
e) 0.05 mm
Correct answer: c) 0.01 mm or 0.001"
What tool is used to set the threading tool at a right angle to the workpiece axis?
a) Dial indicator
b) Tool height gauge
c) Combination square
d) Thread centre gauge (fishtail)
e) Bevel protractor
Correct answer: d) Thread centre gauge (fishtail)
Sensitive tool used to measure the depth of small holes and bores?
a) Vernier depth gauge
b) Dial depth gauge
c) Depth micrometer
d) Inside micrometer
e) Steel rule
Correct answer: c) Depth micrometer
Most effective type of hearing protection?
a) Earplugs only
b) Earmuffs only
c) Noise-cancelling headphones
d) Plugs and earmuffs
e) Cotton inserts
Correct answer: d) Plugs and earmuffs
4|Page
