OSHA 510 EXAM NEWEST EXAM 2025-2026 |
COMPLETE QUESTIONS AND CORRECT ANSWERS |
GRADED A+ | LATEST EXAM | VERIFIED ANSWERS
The maximum travel distance fire extinguisher
from any
point of the protection are to
the nearest
____ shall not exceed 100 feet
All , whether paid for by the hand and power tools
employee,
shall be tested daily.
its important that all the 6&6
employees are
protected from fall hazards
when working on
unguarded surface more
than
_____________________ fe
et
above a lower level, or
working at
_____________________ heig
ht
above dangerous equipment
what is the maximum force 1,800 pounds
that can be
exerted n the human body
with a fall arrest system
when stopping a fall, a ___ Personal fall arrest system
shall bring an
employee to a complete stop
and limit the maximum
deceleration distance at 6
feet.
Personal fall arrest system, it has a maximum arresting force of 5000 pounds or 5
,when stopping a fall be times the potential impact energy of an employee
rigged such that:
according to the 42
1926.502(b)(1), the top rail of
a guardrail system must be a
height of ___ inches +/- 3
inches above the working
levels.
accident prevention signs such visible
as; danger, caution and exit
signs shall be ___ work is
being preformed.
danger indicate that an ___ immediate
hazard exist.
caution signs indicate a p____ h potential hazard
____________________ exists.
traffic barricades must manual for uniform traffic control devices
conform to:
the electrode holder end of 10 ft
the cable must be free
from repair or splice for
minimum distance of at
least ___ feet from end of
cable.
multiple lift assemblies 7
must be rigged at least __
feet apart
, seprate oxygen and fuel 20 ft
cylinder by a distance
of at least ___ft
PPE appropriate for welder welder helmet, apron, etc
would include
whenever practicable, all Guarded and shielded
arc welding and cutting
operation shall be
_________________ to
protect
employees and other persons
working the vicinity.
what is the importance of that valves are at base of torch or in front of regulations
prevention back flow
failure to inspect for on Oils and grease
regulator fitting,
valves, or the cap threads on
a cylinder of oxygen can
result in fire or explosion.
an "assured equipment not part of the permanent wiring of the building or structures
grounding
conductor program" deals
with the cord set and
receptacle which are:
at 50 volts or higher is Guardung
required against
accident contract by cabinet,
other forms if enclosed, or
by location in a room or
enclosed accessible only
to qualified persons
(electrician)
The practice of connecting Bonding
two metallic object to
prevent static spark is
called:
COMPLETE QUESTIONS AND CORRECT ANSWERS |
GRADED A+ | LATEST EXAM | VERIFIED ANSWERS
The maximum travel distance fire extinguisher
from any
point of the protection are to
the nearest
____ shall not exceed 100 feet
All , whether paid for by the hand and power tools
employee,
shall be tested daily.
its important that all the 6&6
employees are
protected from fall hazards
when working on
unguarded surface more
than
_____________________ fe
et
above a lower level, or
working at
_____________________ heig
ht
above dangerous equipment
what is the maximum force 1,800 pounds
that can be
exerted n the human body
with a fall arrest system
when stopping a fall, a ___ Personal fall arrest system
shall bring an
employee to a complete stop
and limit the maximum
deceleration distance at 6
feet.
Personal fall arrest system, it has a maximum arresting force of 5000 pounds or 5
,when stopping a fall be times the potential impact energy of an employee
rigged such that:
according to the 42
1926.502(b)(1), the top rail of
a guardrail system must be a
height of ___ inches +/- 3
inches above the working
levels.
accident prevention signs such visible
as; danger, caution and exit
signs shall be ___ work is
being preformed.
danger indicate that an ___ immediate
hazard exist.
caution signs indicate a p____ h potential hazard
____________________ exists.
traffic barricades must manual for uniform traffic control devices
conform to:
the electrode holder end of 10 ft
the cable must be free
from repair or splice for
minimum distance of at
least ___ feet from end of
cable.
multiple lift assemblies 7
must be rigged at least __
feet apart
, seprate oxygen and fuel 20 ft
cylinder by a distance
of at least ___ft
PPE appropriate for welder welder helmet, apron, etc
would include
whenever practicable, all Guarded and shielded
arc welding and cutting
operation shall be
_________________ to
protect
employees and other persons
working the vicinity.
what is the importance of that valves are at base of torch or in front of regulations
prevention back flow
failure to inspect for on Oils and grease
regulator fitting,
valves, or the cap threads on
a cylinder of oxygen can
result in fire or explosion.
an "assured equipment not part of the permanent wiring of the building or structures
grounding
conductor program" deals
with the cord set and
receptacle which are:
at 50 volts or higher is Guardung
required against
accident contract by cabinet,
other forms if enclosed, or
by location in a room or
enclosed accessible only
to qualified persons
(electrician)
The practice of connecting Bonding
two metallic object to
prevent static spark is
called:
