CTS, Certified Technology Specialist Exam |232
Questions with accurate answers
A) 1 Ans✓✓✓ Chapter 12 Question 12
On a drawing with a 1:50 scale, 2 centimeters equal how many meters?
A) 1
B) 2
C) 1/2
D) None of the above
A) 24 Ans✓✓✓ Chapter 12 Question 13
On a drawing using a 1/4 scale, 6 inches equal how many feet?
A) 24
B) 8
C) 16
D) None of the above
A) 25.4 x 10 = 254 mm Ans✓✓✓ Chapter 12 Question 15
Which of the following equations allows you to convert a measurement
of 10 inches into an equivalent measurement in millimeters?
A) 25.4 x 10 = 254 mm
,B) 3.94 x 10 = 39.4 mm
C) 25. = 2.54 mm
D) 3. = .394 mm
A) A IP address Ans✓✓✓ Chapter 19 Question 4
In order to communicate with devices installed onto a TCP/IP network,
what must each device have?
A) An IP address
B) A wireless card
C) A web address
D) A TCP card
A) A signal that has many varying states is called an analog signal.
Ans✓✓✓ Chapter 3 Question 2
A signal that has many varying states is called a(n) ....... signal.
A) Analog signal
B) Fluctuating signal
C) Dimmer Signal
D) Digital Signal
A) A task that cannot being before another task is complete Ans✓✓✓
Chapter 20 Question 3
,What is a dependency within a project task schedule?
A) A task that cannot begin before another task is complete
B) A task that must be completed by a specific date
C) A task that will be required if specific conditions occur at the project
site
D) An optional task that the client can determine is needed once the
project is underway
A) Adding compression to the microphone signal chain Ans✓✓✓
Chapter 23 Question 9
Which of the following is NOT a method of addressing feeback within
an audio system?
A) adding compression to the microphone signal chain
B) Keeping the microphone as close to the sound source as possible
C) Keeping the loudspeakers in front of and as far from the microphones
as possible
D) Turning down or muting all unused microphones
A) Addresses Ans✓✓✓ Chapter 6 Question 8
IP deals with which of the following on a network?
A) Addresses
B) Names
, C) Routes
D) Versions
A) AFF Ans✓✓✓ Chapter 12 Question 10
Which abbreviation, along with a measurement given on a drawing, tells
you how high on a wall an interface plate should be installed?
A) AFF
B) FUT
C) SCN
D) NIC
A) Ambient noise and reverberation Ans✓✓✓ Chapter 13 Question 4
What is the primary issue that the AV designer should assess when
reviewing the acoustic environment at a client site?
A) Ambient noise and reverberation
B) The required loudness level of the AV system
C) The optimum locations for Av system loudspeakers
D) The audio system needs for the presenter and presenter area within
the room
A) Amperes Ans✓✓✓ Chapter 8 Question 2
Current is measure in ......... .
Questions with accurate answers
A) 1 Ans✓✓✓ Chapter 12 Question 12
On a drawing with a 1:50 scale, 2 centimeters equal how many meters?
A) 1
B) 2
C) 1/2
D) None of the above
A) 24 Ans✓✓✓ Chapter 12 Question 13
On a drawing using a 1/4 scale, 6 inches equal how many feet?
A) 24
B) 8
C) 16
D) None of the above
A) 25.4 x 10 = 254 mm Ans✓✓✓ Chapter 12 Question 15
Which of the following equations allows you to convert a measurement
of 10 inches into an equivalent measurement in millimeters?
A) 25.4 x 10 = 254 mm
,B) 3.94 x 10 = 39.4 mm
C) 25. = 2.54 mm
D) 3. = .394 mm
A) A IP address Ans✓✓✓ Chapter 19 Question 4
In order to communicate with devices installed onto a TCP/IP network,
what must each device have?
A) An IP address
B) A wireless card
C) A web address
D) A TCP card
A) A signal that has many varying states is called an analog signal.
Ans✓✓✓ Chapter 3 Question 2
A signal that has many varying states is called a(n) ....... signal.
A) Analog signal
B) Fluctuating signal
C) Dimmer Signal
D) Digital Signal
A) A task that cannot being before another task is complete Ans✓✓✓
Chapter 20 Question 3
,What is a dependency within a project task schedule?
A) A task that cannot begin before another task is complete
B) A task that must be completed by a specific date
C) A task that will be required if specific conditions occur at the project
site
D) An optional task that the client can determine is needed once the
project is underway
A) Adding compression to the microphone signal chain Ans✓✓✓
Chapter 23 Question 9
Which of the following is NOT a method of addressing feeback within
an audio system?
A) adding compression to the microphone signal chain
B) Keeping the microphone as close to the sound source as possible
C) Keeping the loudspeakers in front of and as far from the microphones
as possible
D) Turning down or muting all unused microphones
A) Addresses Ans✓✓✓ Chapter 6 Question 8
IP deals with which of the following on a network?
A) Addresses
B) Names
, C) Routes
D) Versions
A) AFF Ans✓✓✓ Chapter 12 Question 10
Which abbreviation, along with a measurement given on a drawing, tells
you how high on a wall an interface plate should be installed?
A) AFF
B) FUT
C) SCN
D) NIC
A) Ambient noise and reverberation Ans✓✓✓ Chapter 13 Question 4
What is the primary issue that the AV designer should assess when
reviewing the acoustic environment at a client site?
A) Ambient noise and reverberation
B) The required loudness level of the AV system
C) The optimum locations for Av system loudspeakers
D) The audio system needs for the presenter and presenter area within
the room
A) Amperes Ans✓✓✓ Chapter 8 Question 2
Current is measure in ......... .
