SHP FINAL WITH COMPLETE
SOLUTIONS 100% 2023/2024
True - answer-The firefighter may be installed next to a stand-alone battery
smoke detector
False - answer-When performing a full system test, you may bypass any open
doors or windows
Always enable the emergency - answer-When programming an skey1,you must
False - answer-When running power to the take345,polarity doesn't apply
Audible alarm (7) - answer-When programming the emergency key for the
skey1,which zone/sensor type is used.
True - answer-When installing a smkt3,you must use the included screws and
anchors
True - answer-When installing the firefighter, it is required to test the customers
existing smoke detectors
Between 6"(15cm) and 2'(61cm) from floor - answer-When installing a Dw21,
where is the approved location for the sensor
Provided double sided tape - answer-When installing a dw11 on a vinyl or metal
frame, what should primarily use to mount the sensor
Beans & wire caps - answer-Which of the following materials can you use to
group multiple ground terminals in a takeover.
Smoke detector - answer-Which of the following sensors are you not allowed to
program using a translator
, True - answer-When installing the take345, you must always test the new 12v
battery before using it.
16.5 - answer-What is the output voltage of transformer used to power the sky
control
12" - answer-What is the minimum distance for placement of a co3 from the
corners of the wall
False - answer-The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14 - answer-How would you program a co3 if mounted on a hallway
wall
False - answer-When installing a translator, you must program all of the existing
sensors as new equipment on the panel
True - answer-The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze - answer-Which of the
following zone/sensor types are correct when programming an smkt3
7ft - answer-What it the correct height ar which to install the Pir2
Loop 2 - answer-When programming a Dw21 what loop number is used
True - answer-When programming a sensor into a sky control panel, you can
type in the serial number or learn it in by triggering the device.
Loop 1 Zone 3 - answer-How would you program a gb2 when it is mounted on a
master bedroom ceiling
True - answer-Panic pendants are programmed as an audible alarm(type 07)
True - answer-When installing the take 345 you must ensure that the transformer
is supplying power to the power supply before connecting the battery
SOLUTIONS 100% 2023/2024
True - answer-The firefighter may be installed next to a stand-alone battery
smoke detector
False - answer-When performing a full system test, you may bypass any open
doors or windows
Always enable the emergency - answer-When programming an skey1,you must
False - answer-When running power to the take345,polarity doesn't apply
Audible alarm (7) - answer-When programming the emergency key for the
skey1,which zone/sensor type is used.
True - answer-When installing a smkt3,you must use the included screws and
anchors
True - answer-When installing the firefighter, it is required to test the customers
existing smoke detectors
Between 6"(15cm) and 2'(61cm) from floor - answer-When installing a Dw21,
where is the approved location for the sensor
Provided double sided tape - answer-When installing a dw11 on a vinyl or metal
frame, what should primarily use to mount the sensor
Beans & wire caps - answer-Which of the following materials can you use to
group multiple ground terminals in a takeover.
Smoke detector - answer-Which of the following sensors are you not allowed to
program using a translator
, True - answer-When installing the take345, you must always test the new 12v
battery before using it.
16.5 - answer-What is the output voltage of transformer used to power the sky
control
12" - answer-What is the minimum distance for placement of a co3 from the
corners of the wall
False - answer-The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14 - answer-How would you program a co3 if mounted on a hallway
wall
False - answer-When installing a translator, you must program all of the existing
sensors as new equipment on the panel
True - answer-The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze - answer-Which of the
following zone/sensor types are correct when programming an smkt3
7ft - answer-What it the correct height ar which to install the Pir2
Loop 2 - answer-When programming a Dw21 what loop number is used
True - answer-When programming a sensor into a sky control panel, you can
type in the serial number or learn it in by triggering the device.
Loop 1 Zone 3 - answer-How would you program a gb2 when it is mounted on a
master bedroom ceiling
True - answer-Panic pendants are programmed as an audible alarm(type 07)
True - answer-When installing the take 345 you must ensure that the transformer
is supplying power to the power supply before connecting the battery
