OLERE Study Guide 2023 – Complete Practice
Material with Verified Answer
OLERE 2023 Practice Exam: 100 Questions & Answers
Section 1: Safety and Personal Survival (Questions 1-20)
1. What is the primary purpose of a Safety Data Sheet (SDS)?
A) To list the price of chemicals
B) To provide detailed information on the hazards of a chemical and how to work
safely with it
C) To track chemical inventory
D) To serve as a shipping manifest
2. The "RACE" acronym in fire safety stands for:
A) Run, Alert, Contain, Evacuate
B) Rescue, Alarm, Confine, Extinguish
C) Remove, Activate, Control, Exit
D) Respond, Announce, Combat, Escape
3. A Class B fire involves which type of material?
A) Combustible metals
B) Energized electrical equipment
C) Flammable liquids and gases
D) Ordinary combustibles (wood, paper)
4. What is the minimum required Personal Flotation Device (PFD) for each
person on board a vessel?
A) A Type I PFD
B) A Type II PFD
C) A Type III PFD
D) A Type IV throwable device
,5. The "STOP" principle in survival stands for:
A) Start, Think, Observe, Plan
B) Sit, Think, Observe, Plan
C) Signal, Travel, Organize, Protect
D) Stay, Talk, Operate, Proceed
6. Hypothermia is defined as a core body temperature below:
A) 95°F (35°C)
B) 98.6°F (37°C)
C) 100°F (37.8°C)
D) 90°F (32°C)
7. What is the correct first aid for a severe, bleeding wound?
A) Apply a tourniquet as a first resort
B) Apply direct pressure with a sterile dressing
C) Immerse the wound in water
D) Apply ice directly to the wound
8. A confined space entry permit is required because:
A) It increases workplace efficiency
B) It is an OSHA and company-mandated procedure to ensure safety controls are
in place before entry
C) It is only needed for spaces deeper than 10 feet
D) It is a formality for record-keeping
9. The purpose of a "Tagout" lock is to:
A) Identify the owner of a tool
B) Prevent the accidental energizing of equipment during maintenance
C) Mark a hazardous area
D) Secure a storage container
10. In a man-overboard situation, the first action should be to:
A) Jump in after the person
B) Slow the vessel and throw a flotation device
, C) Radio for help immediately
D) Sound the general alarm
11. The correct sequence for using a fire extinguisher is:
A) Aim, Squeeze, Sweep, Pull
B) Pull, Aim, Squeeze, Sweep
C) Squeeze, Pull, Aim, Sweep
D) Sweep, Aim, Pull, Squeeze
12. Which signal is recognized internationally as a distress signal?
A) Waving both arms over your head
B) Three of any signal (three blasts, three fires)
C) A single red flare
D) Shouting "Help" repeatedly
13. Heat stroke is characterized by:
A) Shivering and cold skin
B) Profuse sweating
C) Hot, dry skin and confusion
D) Pale and clammy skin
14. The primary hazard of Hydrogen Sulfide (H2S) is that it:
A) Is highly flammable
B) Causes skin irritation
C) Is a toxic gas that can cause respiratory paralysis and death
D) Has a strong, pleasant odor
15. A "Hot Work Permit" is required for operations such as:
A) Using a computer
B) Welding, grinding, or cutting
C) Operating a crane
D) Cleaning with solvents
16. The purpose of a "Job Safety Analysis" (JSA) is to:
A) Assign blame for accidents
Material with Verified Answer
OLERE 2023 Practice Exam: 100 Questions & Answers
Section 1: Safety and Personal Survival (Questions 1-20)
1. What is the primary purpose of a Safety Data Sheet (SDS)?
A) To list the price of chemicals
B) To provide detailed information on the hazards of a chemical and how to work
safely with it
C) To track chemical inventory
D) To serve as a shipping manifest
2. The "RACE" acronym in fire safety stands for:
A) Run, Alert, Contain, Evacuate
B) Rescue, Alarm, Confine, Extinguish
C) Remove, Activate, Control, Exit
D) Respond, Announce, Combat, Escape
3. A Class B fire involves which type of material?
A) Combustible metals
B) Energized electrical equipment
C) Flammable liquids and gases
D) Ordinary combustibles (wood, paper)
4. What is the minimum required Personal Flotation Device (PFD) for each
person on board a vessel?
A) A Type I PFD
B) A Type II PFD
C) A Type III PFD
D) A Type IV throwable device
,5. The "STOP" principle in survival stands for:
A) Start, Think, Observe, Plan
B) Sit, Think, Observe, Plan
C) Signal, Travel, Organize, Protect
D) Stay, Talk, Operate, Proceed
6. Hypothermia is defined as a core body temperature below:
A) 95°F (35°C)
B) 98.6°F (37°C)
C) 100°F (37.8°C)
D) 90°F (32°C)
7. What is the correct first aid for a severe, bleeding wound?
A) Apply a tourniquet as a first resort
B) Apply direct pressure with a sterile dressing
C) Immerse the wound in water
D) Apply ice directly to the wound
8. A confined space entry permit is required because:
A) It increases workplace efficiency
B) It is an OSHA and company-mandated procedure to ensure safety controls are
in place before entry
C) It is only needed for spaces deeper than 10 feet
D) It is a formality for record-keeping
9. The purpose of a "Tagout" lock is to:
A) Identify the owner of a tool
B) Prevent the accidental energizing of equipment during maintenance
C) Mark a hazardous area
D) Secure a storage container
10. In a man-overboard situation, the first action should be to:
A) Jump in after the person
B) Slow the vessel and throw a flotation device
, C) Radio for help immediately
D) Sound the general alarm
11. The correct sequence for using a fire extinguisher is:
A) Aim, Squeeze, Sweep, Pull
B) Pull, Aim, Squeeze, Sweep
C) Squeeze, Pull, Aim, Sweep
D) Sweep, Aim, Pull, Squeeze
12. Which signal is recognized internationally as a distress signal?
A) Waving both arms over your head
B) Three of any signal (three blasts, three fires)
C) A single red flare
D) Shouting "Help" repeatedly
13. Heat stroke is characterized by:
A) Shivering and cold skin
B) Profuse sweating
C) Hot, dry skin and confusion
D) Pale and clammy skin
14. The primary hazard of Hydrogen Sulfide (H2S) is that it:
A) Is highly flammable
B) Causes skin irritation
C) Is a toxic gas that can cause respiratory paralysis and death
D) Has a strong, pleasant odor
15. A "Hot Work Permit" is required for operations such as:
A) Using a computer
B) Welding, grinding, or cutting
C) Operating a crane
D) Cleaning with solvents
16. The purpose of a "Job Safety Analysis" (JSA) is to:
A) Assign blame for accidents
