NACE CIP 1 CBT EXAM PRACTICE
QUESTIONS AND ANSWERS
Dew point is the temperature at which - Correct Answers -condensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of action is to: - Correct
Answers -Document the problem and advise the Contractor and Owner's
representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive blast
cleaning and conventional airspray, the coating inspector should perform a - Correct
Answers -blotter test for the presence of oil and water.
Upon arrival of coating materials, the inspector should - Correct Answers -observe and
document the amount of material and batch numbers.
According to the NACE attestation, when is it OK to accept a gift from a contractor? -
Correct Answers -Never acceptable.
What should you do if you find discrepancies between the specification and the coating
manufacturers technical data sheet? - Correct Answers -Seek written clarification from
the coating manufacturer.
Which of the following are generally components of the inspection reports? - Correct
Answers -Results of inspection tests, Location of work and Details of preparation and
application.
Inspection reports typically provide sufficient detail permitting the owner to evaluate? -
Correct Answers -Contractors performance, inspectors performance, job progress and
work interruptions.
Relative humidity is - Correct Answers -a measure of the amount of moisture in the air
compared to saturation level.
Galvanic corrosion occurs on which of the following substrates? - Correct Answers -
Metal
, When applying Thermal Spray Coatings the specification is most likely to reference: -
Correct Answers -SSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector
should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT)
gauge? - Correct Answers -2.5 cm (1 inch)
Polymerization is the process of? - Correct Answers -Monomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often
caused by poor application technique is called: - Correct Answers -Holiday
Checking is: - Correct Answers -a fine crack in the surface of a coating that rarely
reaches the substrate.
Inspection documentation is important because: - Correct Answers -Owners use the
documentation for a variety of purposes.
An Inspectors personal log book should contain: - Correct Answers -No comments
regarding the application team.
You have just received your NACE CIP Level 1 certification when you are asked to
supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of
action is to: - Correct Answers -Review the NACE Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information about ALL
of the following EXCEPT: - Correct Answers -How the item was coated.
Non Conformance Reports are completed by the Inspector: - Correct Answers -When
the Inspector and Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - Correct
Answers -The Inspector may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure
is: - Correct Answers -Galvanic Corrosion
What is used to determine compressed air cleanliness? - Correct Answers -Profilometer
Osmotic blistering is most likely to occur as a result of: - Correct Answers -Airless spray
application.
When performing tests for oil and grease using an ultra violet light, the NACE Inspector
should be aware that: - Correct Answers -Synthetic oil or grease may not be identified.
QUESTIONS AND ANSWERS
Dew point is the temperature at which - Correct Answers -condensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of action is to: - Correct
Answers -Document the problem and advise the Contractor and Owner's
representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive blast
cleaning and conventional airspray, the coating inspector should perform a - Correct
Answers -blotter test for the presence of oil and water.
Upon arrival of coating materials, the inspector should - Correct Answers -observe and
document the amount of material and batch numbers.
According to the NACE attestation, when is it OK to accept a gift from a contractor? -
Correct Answers -Never acceptable.
What should you do if you find discrepancies between the specification and the coating
manufacturers technical data sheet? - Correct Answers -Seek written clarification from
the coating manufacturer.
Which of the following are generally components of the inspection reports? - Correct
Answers -Results of inspection tests, Location of work and Details of preparation and
application.
Inspection reports typically provide sufficient detail permitting the owner to evaluate? -
Correct Answers -Contractors performance, inspectors performance, job progress and
work interruptions.
Relative humidity is - Correct Answers -a measure of the amount of moisture in the air
compared to saturation level.
Galvanic corrosion occurs on which of the following substrates? - Correct Answers -
Metal
, When applying Thermal Spray Coatings the specification is most likely to reference: -
Correct Answers -SSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector
should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT)
gauge? - Correct Answers -2.5 cm (1 inch)
Polymerization is the process of? - Correct Answers -Monomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often
caused by poor application technique is called: - Correct Answers -Holiday
Checking is: - Correct Answers -a fine crack in the surface of a coating that rarely
reaches the substrate.
Inspection documentation is important because: - Correct Answers -Owners use the
documentation for a variety of purposes.
An Inspectors personal log book should contain: - Correct Answers -No comments
regarding the application team.
You have just received your NACE CIP Level 1 certification when you are asked to
supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of
action is to: - Correct Answers -Review the NACE Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information about ALL
of the following EXCEPT: - Correct Answers -How the item was coated.
Non Conformance Reports are completed by the Inspector: - Correct Answers -When
the Inspector and Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - Correct
Answers -The Inspector may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure
is: - Correct Answers -Galvanic Corrosion
What is used to determine compressed air cleanliness? - Correct Answers -Profilometer
Osmotic blistering is most likely to occur as a result of: - Correct Answers -Airless spray
application.
When performing tests for oil and grease using an ultra violet light, the NACE Inspector
should be aware that: - Correct Answers -Synthetic oil or grease may not be identified.
