1
BASIC AND ADVANCED RIGGING PRACTICES EXAM
FULL PACKAGE QUESTIONS ANSWERS AND
RATIONALES 2026-27 LATEST VERSION
Subject: Construction and Industrial Rigging
Course Code: RIGG-101
Description:
This comprehensive examination assesses mastery of safe rigging practices for construction,
industrial, and entertainment applications. Candidates will demonstrate knowledge of load
weight estimation, sling angle calculations, rigging hardware identification and inspection,
hitch configurations, and safe lifting procedures. The exam covers wire rope, synthetic, and
chain slings; shackles, hooks, and below-the-hook lifting devices; OSHA and ASME regulatory
requirements; hand and voice signal communication; and emergency procedures. Clinical
decision-making is emphasized through scenario-based questions requiring application of
rigging principles, hazard identification, and regulatory compliance. Questions reflect current
standards including ASME B30 series, OSHA 1910.184 and 1926.251, and NCCCO rigger
certification requirements.
SECTION 1: Questions 1–50
1. A load weighs 4,500 lbs and is being lifted by a single vertical sling.
What is the tension in the sling?
A) 2,250 lbs
B) 4,500 lbs
C) 9,000 lbs
D) 1,125 lbs
Rationale: In a single vertical lift, the tension equals the load weight.
There is no angle or multiple-leg sharing to affect the calculation.
2. What is the first step in any rigging operation?
,2
A) Select the appropriate sling
B) Determine the weight of the load
C) Inspect the crane
D) Clear the lift zone
Rationale: Determining the load weight is the essential first step
before selecting rigging equipment or planning the lift. All rigging
capacities depend on knowing the load weight.
3. What is the recommended action when lifting a load longer than
_______?
A) 8 feet
B) 10 feet
C) 12 feet
D) 15 feet
Rationale: The recommendation when lifting a load longer than 12
feet is to use two choker hitches to provide better load control and
stability.
4. A 1-inch, 3-leg bridle wire rope sling rigged at a 45-degree angle is
rated for 18 tons. If a fourth leg is added, the capacity will increase
by:
A) 4.5 tons
B) 6 tons
C) 0 lbs (no increase)
D) 2 tons
,3
Rationale: Adding a fourth leg to a bridle sling does not increase the
rated capacity. The capacity is determined by the angle of the legs
and the weakest leg.
5. According to OSHA regulations, a hook must be removed from
service when the throat opening exceeds what percentage of its
original opening?
A) 10%
B) 15%
C) 20%
D) 25%
Rationale: OSHA requires hook replacement if the throat opening
exceeds 15% of its original size. This deformation indicates
overloading or metal fatigue.
6. What provides additional control of a load being lifted?
A) Tag lines
B) Safety harnesses
C) Tag lines
D) Outriggers
Rationale: Tag lines are used to help control the load, preventing it
from swinging or rotating during the lift. They allow ground
personnel to maintain load stability.
7. When two cranes are lifting 100 tons and Crane A has 40% of the
load, how much weight will Crane B have on its hook?
, 4
A) 40,000 lbs
B) 80,000 lbs
C) 120,000 lbs
D) 160,000 lbs
Rationale: 100 tons = 200,000 lbs. Crane A has 40% (80,000 lbs), so
Crane B has 60% (120,000 lbs). The two cranes share the total load.
8. The process that attempts to identify hazards and devise plans to
overcome or eliminate them is called:
A) Risk assessment
B) Lift plan
C) Safety audit
D) Pre-lift inspection
Rationale: A lift plan is a methodical process that identifies potential
hazards and develops plans to overcome or eliminate them before the
lift begins.
9. What type of rope will stretch the furthest under a sustained load?
A) Nylon
B) Polyester
C) Polypropylene
D) #1 Manila
Rationale: #1 Manila natural fiber rope stretches the furthest under a
sustained load compared to synthetic alternatives.
10. How do you find the safe working load (SWL) for a single vertical
wire rope sling using the rule of thumb?
BASIC AND ADVANCED RIGGING PRACTICES EXAM
FULL PACKAGE QUESTIONS ANSWERS AND
RATIONALES 2026-27 LATEST VERSION
Subject: Construction and Industrial Rigging
Course Code: RIGG-101
Description:
This comprehensive examination assesses mastery of safe rigging practices for construction,
industrial, and entertainment applications. Candidates will demonstrate knowledge of load
weight estimation, sling angle calculations, rigging hardware identification and inspection,
hitch configurations, and safe lifting procedures. The exam covers wire rope, synthetic, and
chain slings; shackles, hooks, and below-the-hook lifting devices; OSHA and ASME regulatory
requirements; hand and voice signal communication; and emergency procedures. Clinical
decision-making is emphasized through scenario-based questions requiring application of
rigging principles, hazard identification, and regulatory compliance. Questions reflect current
standards including ASME B30 series, OSHA 1910.184 and 1926.251, and NCCCO rigger
certification requirements.
SECTION 1: Questions 1–50
1. A load weighs 4,500 lbs and is being lifted by a single vertical sling.
What is the tension in the sling?
A) 2,250 lbs
B) 4,500 lbs
C) 9,000 lbs
D) 1,125 lbs
Rationale: In a single vertical lift, the tension equals the load weight.
There is no angle or multiple-leg sharing to affect the calculation.
2. What is the first step in any rigging operation?
,2
A) Select the appropriate sling
B) Determine the weight of the load
C) Inspect the crane
D) Clear the lift zone
Rationale: Determining the load weight is the essential first step
before selecting rigging equipment or planning the lift. All rigging
capacities depend on knowing the load weight.
3. What is the recommended action when lifting a load longer than
_______?
A) 8 feet
B) 10 feet
C) 12 feet
D) 15 feet
Rationale: The recommendation when lifting a load longer than 12
feet is to use two choker hitches to provide better load control and
stability.
4. A 1-inch, 3-leg bridle wire rope sling rigged at a 45-degree angle is
rated for 18 tons. If a fourth leg is added, the capacity will increase
by:
A) 4.5 tons
B) 6 tons
C) 0 lbs (no increase)
D) 2 tons
,3
Rationale: Adding a fourth leg to a bridle sling does not increase the
rated capacity. The capacity is determined by the angle of the legs
and the weakest leg.
5. According to OSHA regulations, a hook must be removed from
service when the throat opening exceeds what percentage of its
original opening?
A) 10%
B) 15%
C) 20%
D) 25%
Rationale: OSHA requires hook replacement if the throat opening
exceeds 15% of its original size. This deformation indicates
overloading or metal fatigue.
6. What provides additional control of a load being lifted?
A) Tag lines
B) Safety harnesses
C) Tag lines
D) Outriggers
Rationale: Tag lines are used to help control the load, preventing it
from swinging or rotating during the lift. They allow ground
personnel to maintain load stability.
7. When two cranes are lifting 100 tons and Crane A has 40% of the
load, how much weight will Crane B have on its hook?
, 4
A) 40,000 lbs
B) 80,000 lbs
C) 120,000 lbs
D) 160,000 lbs
Rationale: 100 tons = 200,000 lbs. Crane A has 40% (80,000 lbs), so
Crane B has 60% (120,000 lbs). The two cranes share the total load.
8. The process that attempts to identify hazards and devise plans to
overcome or eliminate them is called:
A) Risk assessment
B) Lift plan
C) Safety audit
D) Pre-lift inspection
Rationale: A lift plan is a methodical process that identifies potential
hazards and develops plans to overcome or eliminate them before the
lift begins.
9. What type of rope will stretch the furthest under a sustained load?
A) Nylon
B) Polyester
C) Polypropylene
D) #1 Manila
Rationale: #1 Manila natural fiber rope stretches the furthest under a
sustained load compared to synthetic alternatives.
10. How do you find the safe working load (SWL) for a single vertical
wire rope sling using the rule of thumb?