5/18/25, 4:38 PM ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND CORRECT ANSWERS | ALREADY GRADED A+ | LATE…
ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND
CORRECT ANSWERS | ALREADY GRADED A+ | LATEST EXAM | VERIFIED
ANSWERS
Terms in this set (103)
1. Per ASNT Section XI, NDE personnel shall be recertified:
A. every 5 years by re-examination
B.
B. every 3 years by retraining and retesting
C. every 3 years based on continuing satisfactory performance
D. annually by retraining
2. Per SNT-TC-1A, when an employee leaves his employer:
A. his certification automatically transfers to his new employer
B.
B. his certification is automatically terminated
C. he must take an examination to be certified by the new
company
D. he may not be certified by the new employer for at least 3
months
3. Per SNT-TC-1A, certification of NDE personnel is the
responsibility of the:
D. A. ASME
B. manufacturer
C. NRC
D. employer
4. A variation or interpretation in the normal physical
structure or configuration of a part is called a:
B. A. Flaw
B. discontinuity
C. defect
D. fault
… 1/20
,5/18/25, 4:38 PM ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND CORRECT ANSWERS | ALREADY GRADED A+ | LATE…
5. Indications caused by repeatd loading, bending or
by vibrating stresses are called:
D. A. mass hardness
B. lamellar testing
C. hot tears
D. fatigue cracks
6. A group of joining processes which produces
coalescence of materials by heating them to a suitable
tempertaure and by using filler metal having a liquidus
below 450 degree C (840 degree F) and below the
B.
solidus of the base metal is called:
A. brazing
B. soldering
C. resistance welding
D. arc welding
7. SCC is a synergistic action of:
A. steel and cracks
B.
B. stress and corrosion
C. structure and coatings
D. slag and craters
8. Severe grinding cracks appear as:
A. wave-like patterns
C.
B. widely
C. lattice
D. deep crevices
9. Grinding cracks are caused by:
A. too light of pressure during grinding
B.
B. overheating during grinding
C. grinding too large of an area
D. grinding with very fast motion of the grinder
… 2/20
, 5/18/25, 4:38 PM ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND CORRECT ANSWERS | ALREADY GRADED A+ | LATE…
10. A process that joins two members together by using
capillary action to flow the filler material is called:
B. A. soldering if the temperature exceeds 840 degrees F
B. brazing if the temperature exceeds 840 degrees F
C. resistance welding
D. oxy-fuel gas welding
11. A condition that is of such size, shape, type and
location that is detrimental to the useful service of the
part is called:
C.
A. a flaw
B. a discontinuity
C. a defect
D. an indication
12. Mass hardness of a product is caused by improper:
A. weld process
D.
B. forging
C. casting
D. heat treatment
13. The use of this symbol on a drawing indicates a:
A. flare V weld on both sides
C.
B. fillet weld on both sides
C. double V-groove weld
D. V-groove weld on the other side
14. Unfused chaplets are associated with:
A. forging
D.
B. rolling
C. extruding
D. casting
15. The actual throat of a weld is the:
A. actualdistance from the face of the weld to the vertical leg.
B.
B. shortest distance from the root of the weld to its face
… 3/20
ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND
CORRECT ANSWERS | ALREADY GRADED A+ | LATEST EXAM | VERIFIED
ANSWERS
Terms in this set (103)
1. Per ASNT Section XI, NDE personnel shall be recertified:
A. every 5 years by re-examination
B.
B. every 3 years by retraining and retesting
C. every 3 years based on continuing satisfactory performance
D. annually by retraining
2. Per SNT-TC-1A, when an employee leaves his employer:
A. his certification automatically transfers to his new employer
B.
B. his certification is automatically terminated
C. he must take an examination to be certified by the new
company
D. he may not be certified by the new employer for at least 3
months
3. Per SNT-TC-1A, certification of NDE personnel is the
responsibility of the:
D. A. ASME
B. manufacturer
C. NRC
D. employer
4. A variation or interpretation in the normal physical
structure or configuration of a part is called a:
B. A. Flaw
B. discontinuity
C. defect
D. fault
… 1/20
,5/18/25, 4:38 PM ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND CORRECT ANSWERS | ALREADY GRADED A+ | LATE…
5. Indications caused by repeatd loading, bending or
by vibrating stresses are called:
D. A. mass hardness
B. lamellar testing
C. hot tears
D. fatigue cracks
6. A group of joining processes which produces
coalescence of materials by heating them to a suitable
tempertaure and by using filler metal having a liquidus
below 450 degree C (840 degree F) and below the
B.
solidus of the base metal is called:
A. brazing
B. soldering
C. resistance welding
D. arc welding
7. SCC is a synergistic action of:
A. steel and cracks
B.
B. stress and corrosion
C. structure and coatings
D. slag and craters
8. Severe grinding cracks appear as:
A. wave-like patterns
C.
B. widely
C. lattice
D. deep crevices
9. Grinding cracks are caused by:
A. too light of pressure during grinding
B.
B. overheating during grinding
C. grinding too large of an area
D. grinding with very fast motion of the grinder
… 2/20
, 5/18/25, 4:38 PM ASNT VT LEVEL II EXAM (ACTUAL EXAM 2025) | ALL QUESTIONS AND CORRECT ANSWERS | ALREADY GRADED A+ | LATE…
10. A process that joins two members together by using
capillary action to flow the filler material is called:
B. A. soldering if the temperature exceeds 840 degrees F
B. brazing if the temperature exceeds 840 degrees F
C. resistance welding
D. oxy-fuel gas welding
11. A condition that is of such size, shape, type and
location that is detrimental to the useful service of the
part is called:
C.
A. a flaw
B. a discontinuity
C. a defect
D. an indication
12. Mass hardness of a product is caused by improper:
A. weld process
D.
B. forging
C. casting
D. heat treatment
13. The use of this symbol on a drawing indicates a:
A. flare V weld on both sides
C.
B. fillet weld on both sides
C. double V-groove weld
D. V-groove weld on the other side
14. Unfused chaplets are associated with:
A. forging
D.
B. rolling
C. extruding
D. casting
15. The actual throat of a weld is the:
A. actualdistance from the face of the weld to the vertical leg.
B.
B. shortest distance from the root of the weld to its face
… 3/20
