NURSING TEST
BEST EDUCATIONAL RESOURCES FOR STUDENTS
- 5683
- 179
Community
- Seguidores
- Siguiendo
15 Comentarios recibidos
5873 artículos
Nccer review Questions and Answers correct
Nccer review Questions and Answers correct 
What instrument drawing shows an actual representation of a process operating sequence? 
P&ID 
 
 
 
Old packing should be replaced with new packing is: 
In kind 
 
 
 
For most tube bender radius blocks, a 90 degree bend gains approximately _____? 
1 1/2 tube diameter 
 
 
 
Where are rubber gaskets used? 
In a low pressure/ low temperature systems 
 
 
 
The process parameter that is selected for control is called the : 
Controlled variable 
 
 
 
Wh...
- Package deal
- Examen
- • 3 páginas •
-
NCEER • Por  Pogba119
NCCER Module 1 Study Guide Questions and Answers correct
NCCER Module 1 Study Guide Questions and Answers correct 
An example of an unsafe condition on a job site is ______________. 
Inadequate lighting in a stairway 
 
 
 
When other workers are working near an Arc Welding Operation, the standard practice is to 
Screen the work area with welding shields 
 
 
 
What type of fire extinguisher would be used on an electric motor that overheated and caught fire? 
Class C 
 
 
 
One source of lead on some job sites is _____. 
Paint 
 
 
 
Companies with st...
- Package deal
- Examen
- • 1 páginas •
-
NCEER • Por  Pogba119
NCCER Electrical module 3 (intro to electrical circuits) Questions and Answers correct
NCCER Electrical module 3 (intro to electrical circuits) Questions and Answers correct 
a circuit has a source voltage of 50v and a current of 10A, what is the power in watts? 
500w 
 
 
 
voltage is defined as the? 
driving force that makes current flow in a circuit 
 
 
 
if a curcuit has 12 amps of current and the resistance is 20 ohms, the applied voltage is? 
240 volts 
 
 
 
if two 10 ohm resistors are connected in series, what is the total resistance of the resistors? 
20 ohms 
 
 
 
to m...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
Module 7 - NCCER Basic Communication Skill Test Review Questions and Answers correct
Module 7 - NCCER Basic Communication Skill Test Review Questions and Answers correct 
proof read the work for accuracy 
When writing it is important to ... to avoid errors that can cost time and money. 
 
 
 
follow an outline and incorporate your research 
When writing a rough draft of a document your writing should ... 
 
 
 
read the directions completely 
When you have instructions that have a series of steps make sure you ... 
 
 
 
Table of content, indexes, and glossaries 
... are special...
- Package deal
- Examen
- • 1 páginas •
-
NCEER • Por  Pogba119
NCCER Electrical Level 1 Mod 1 Orientation to the Electrical Trade Study Questions and Answers correct
NCCER Electrical Level 1 Mod 1 Orientation to the Electrical Trade Study Questions and Answers correct 
The NCCER electrical training program applies DOL standards and is a 
four-year program 
 
 
 
Entry into an apprenticeship program is likely to require a(n) 
GATB Form Test 
 
 
 
 
The minimum standards for the safe installation of electrical systems can be found in 
the National Electrical Code (NEC) 
 
 
 
OSHA standards for general industry are covered in 
29 CFR, Parts 
 
 
 
The termin...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
NCCER Questions and Answers correct
NCCER Questions and Answers correct 
Most combined power plants use what? 
Gas and steam 
 
 
 
The power grid in the U.S is made up of what? 
3 Major interconnects 
 
 
 
A natural gas used as fuel is what? 
Methane 
 
 
 
As a power industry you must be familiar with safety hazards including what? 
Chemical, Electrical, Thermal, and Mechanical Energy 
 
 
 
A Job of a lab analysis is to determine whether what ? 
Water is properly conditioned 
 
 
 
If technology advanced where hydrogen can be ...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
NCCER Electrical Level 1 Mod 4 Electrical Theory Questions and Answers correct
NCCER Electrical Level 1 Mod 4 Electrical Theory Questions and Answers correct 
Which of the following is true regarding a series circuit? 
The current flow is the same through all resistors. 
 
 
 
Which of the following is true regarding a parallel circuit? 
It has more than one path for current to flow. 
 
 
 
Which of the following is true regarding a series-parallel circuit? 
If a circuit is reduced to an equivalent series circuit, the total resistance is found by adding the loads. 
 
 
 
T...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
ELECTRICAL NCCER Questions and Answers correct
ELECTRICAL NCCER Questions and Answers correct 
The NEC recommends maintaining voltage within a 3% drop. If a branch circuit operates at 240 volts AC. What is the minimum circuit operating volt? 
Answer: 
220. 
 
 
 
What is the name of the connecting device shown in the diagram? 
Answer: 
Split- bolt. 
 
 
 
The volt amperes in an AC circuit is the same as : 
 
 
 
What is the voltage drop for a #8 (16.510 cmil) copper wire at 120v. 215 feet one way and load of 39 amps? 
Answer: 
10.5 
 
 
 
If...
- Package deal
- Examen
- • 12 páginas •
-
NCEER • Por  Pogba119
NCCER Core - construction drawings Questions and Answers
NCCER Core - construction drawings Questions and Answers 
Architectural plans 
Drawings that show the design of the project. Also called architectural drawings. 
 
 
 
Beam 
A large, horizontal structural member made of concrete, steel, stone, wood, or other structural material to provide support above a large opening. 
 
 
 
Blueprints 
The traditional name used to describe construction drawings. 
 
 
 
Civil plans 
Drawings that show the location of the building on the site from an aerial view...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
NCCER Module 2 PreTest Questions and and Answers
NCCER Module 2 PreTest Questions and and Answers 
A procedure used to review job methods and uncover hazards that may have been overlooked is: 
 
a) Site Environment Analysis (SEA) 
b) Job Safety Analysis (JSA) 
Task and Job Analysis (TJA) 
d) Critical Incident Analysis (CIA) 
b) Job Safety Analysis (JSA) 
 
 
 
Incident costs are often classified as: 
 
a) direct and indirect 
b) injury reportable 
c) causes and effects. 
d) time lost 
a) direct and indirect 
 
 
 
Regarding safety, many owners...
- Package deal
- Examen
- • 3 páginas •
-
NCEER • Por  Pogba119
NCCER Test Questions and Answers
NCCER Test Questions and Answers 
trim-out 
The termination of devices and fixtures is completed during a construction phase known as 
 
 
 
Fire alarm systems are commonly required. 
Which of the following is true with regard to commercial electrical work? 
 
 
 
on-site maintenance personnel 
In industrial facilities, the electrical systems are most likely maintained by 
 
 
 
general contractors 
Employers of commercial electricians are often electrical contractors who work as subcontractors...
- Package deal
- Examen
- • 1 páginas •
-
NCEER • Por  Pogba119
NCCER Module 3 Questions and Answers correct
NCCER Module 3 Questions and Answers correct 
Because of the shape of its jaws, which clamp can spread clamping pressure over a wider area than others? 
Hand screw clamp 
 
 
 
What is another name for a machinist's hammer? 
Ball-peen hammer 
 
 
 
What type of clamp is this? 
Spring clamp 
 
 
 
What heavy-duty tool is used to drive posts or other large stakes? 
Sledgehammer 
 
 
 
What is the safest type of utility knife? 
One with a retractable blade 
 
 
 
How many sides does a hexagonal ...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
NCCER 26210 Questions and Answers correct
NCCER 26210 Questions and Answers correct 
A device that trips when a fault current to ground is 6mA or more is designated by UL as _____. 
Class A 
 
 
 
Cartridge fuses used for branch circuit protection must be marked with the ampere rating, interrupting rating (if other than 10,000A), and the _____. 
voltage rating 
 
 
 
Circuit breakers and fuses operate in a similar manner as a boiler's _____. 
pressure relief valve 
 
 
 
Circuits in which the breaker must be highly sensitive to amper...
- Package deal
- Examen
- • 1 páginas •
-
NCEER • Por  Pogba119
Module 00101 Exam NCCER Questions and Answers correct
Module 00101 Exam NCCER Questions and Answers correct 
Poor lighting, excessive noise, and inadequate guards for moving parts are example of 
Unsafe conditions 
 
 
 
Companies with strong safety cultures have lower 
Turnover 
 
 
 
AN unplanned event that may or may not result in property damage is known as a(n) 
Incident 
 
 
 
The activity that consists of breaking a job into it's components tasks and the analyzing each step for potential hazards is called a 
job safety analysis 
 
 
 
A m...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
NCCER 26401 Load Calculations - Feeders and Services Questions and Answers correct
NCCER 26401 Load Calculations - Feeders and Services Questions and Answers correct 
The smallest size locking and grounding type receptacle that may be used to provide shore power for boats is _____. 
30A 
 
 
 
A commercial kitchen with more than six pieces of kitchen equipment is subject to a demand factor of _____. 
65% 
 
 
 
What is the load for 40 non-dwelling unit receptacles? (Assume that the load is not continuous.) 
7,200VA 
 
 
 
Refer to the figure provided. What is the total load of...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
NCCER Electrical Lv 1 MODULE 9 Conductors and Cables Questions and Answers correct
NCCER Electrical Lv 1 MODULE 9 Conductors and Cables Questions and Answers correct 
The slandered system of wire sizes in the United Stated is known as the _______. 
American Wire Gauge (AWG) system 
 
 
 
Wire sizes of No._ or larger are shown only as stranded. 
No.6 
 
 
 
The purpose of stranding is to increase ________. 
The Flexibility of the wire 
 
 
 
A circular mil is a circle that has a diameter of ______. 
1 mil 
 
 
 
A mil is ____. 
0.001 inch 
 
 
 
Aluminum conductors have a _____...
- Package deal
- Examen
- • 4 páginas •
-
NCEER • Por  Pogba119
NCCER Module 2 Questions and Answers correct
NCCER Module 2 Questions and Answers correct 
 
An estimator is preparing a bid for a home remodeling project. She has determined that the new garage needs 324 feet of 2x10 lumber; the new rec room requires 430 feet; and the new upstairs bonus room needs 283 feet. How many feet of 2x10 lumber will be needed? 
1,037 feet 
 
 
 
A plumbing contractor bid the rough-in work for a new three story office building based an estimate of 850 hours of a journey-level plumber's time on the job. After the...
- Package deal
- Examen
- • 14 páginas •
-
NCEER • Por  Pogba119
Nccer test boilermaker Questions and Answers correct
Nccer test boilermaker Questions and Answers correct 
1. Which organization requires a person to be trained in order to operate personal lifting equipment 
a. osha 
b. ansi 
c. nfpa 
d. asme 
A. OSHA 
 
 
 
2. Where would the usage of a RTJ Gasket be found 
e. High pressure system 
f. Low pressure system 
g. Water system 
h. Air system 
e. High pressure system 
 
 
 
3. All of the following are examples of internal manway hardware except 
i. Football washer 
j. Slide fastener 
k. Half washer 
l....
- Package deal
- Examen
- • 11 páginas •
-
NCEER • Por  Pogba119
Ironworker NCCER Questions and Answers correct
Ironworker NCCER Questions and Answers correct 
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED FOR A 3/4" DIAMETER BOLT? 
2 1/4" 
 
 
 
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: 
SPAN 
 
 
 
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE COMPLETED? 
JOIST MUST HAVE BRIDGING INSTALLED 
 
 
 
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO: 
HELP CONTROL THE LOAD 
 
 
 
ITEMS SUCH AS FIELD WE...
- Package deal
- Examen
- • 6 páginas •
-
NCEER • Por  Pogba119
26105 Questions and Answers correct
26105 Questions and Answers correct 
The NEC provides Informative Annexes for _____ 
informational material and examples 
 
 
 
The NEC is divided into 
9 Chapters 
 
 
 
The NEC is published by the ____ 
National Fire Protection Association 
 
 
 
Organizations that test products for safety are ____ 
NRTLs 
 
 
 
Which of the following serves as the introduction to the NEC and provides an overview of the book? 
NEC Article 90 
 
 
 
Which of the following rules identify actions that are allowed...
- Package deal
- Examen
- • 2 páginas •
-
NCEER • Por  Pogba119
Laboratory Financial Management Questions and Answers
(ASB 222) Quiz Questions (Module 1 & 2) and Solutions
ICF PCC Markers Questions and Answers
BPOC FINAL EXAM REVIEW Questions and Answers correct
ICC General Requirements (GR) exam Questions and Answers