AIM Block 1 FInAl ExAM WITH coRREcT AcTUAl QUESTIonS
AnD coRREcTlY WEll DEFInED AnSWERS lATEST 2025 –
2026 AlREADY GRADED A+
The aspect ratio of an aircraft wing is defined as the ratio of the: - ANSWER-Wingspan to the mean
chord.
Which of the following statements concerning density is correct? - ANSWER-If the air pressure is
decreased, the density of the air decreases.
The amount of water vapor present in the air is called: - ANSWER-Humidity
An aircraft's movement around its vertical axis is controlled by the: - ANSWER-Rudder
An aircraft's movement about its lateral axis is controlled by: - ANSWER-Elevators
Which control apparatus is considered to be a secondary flight control? - ANSWER-Trim Tabs
The most common inspection process or procedure which accounts for approximately 80% of all
NDI methods - ANSWER-Visual Inspection
The standard sea level pressure is: - ANSWER-29.92" Hg. at 59 degrees F
Of the three temperature scales, which one is used the least? - ANSWER-Rankine
Which of the following statements is true? - ANSWER-Water vapor weighs 5/8's as much as dry air
, When air holds water vapor, it: - ANSWER-Is lighter than dry air
This inspection method is used to detect surface cracks, pits, subsurface cracks, corrosion on
inner surfaces, and to determine alloy and heat-treat condition: - ANSWER-Eddy Current
This inspection method is a method for detecting cracks, laps, seams, voids, pits, subsurface
holes, and other surface, or slightly subsurface, discontinuities in ferro-magnetic materials: -
ANSWER-Magnetic Particle
A good inspection process to use on nonporous metal and nonmetal components to find
material discontinuities that are open to the surface which may not be evident to normal visual
inspection is: - ANSWER-Dye Penetrant
An NDI inspection technique that uses sound energy moving through the test specimen to
detect flaws is commonly known as: - ANSWER-Ultrasonic Inspection
Tap testing is used to look for which of the following problems: - ANSWER-Delamination of
composite materials
When the weight force is in equilibrium with the lift force, the aircraft: - ANSWER-remains in level
flight
ADs are published to notify aircraft owners and other interested persons of: - ANSWER-Unsafe
conditions which may affect a particular aircraft.
Ailerons control___,Elevators control___,Rudders control____: - ANSWER-Roll; Pitch; Yaw
The purpose of the vertical stabilizer is to provide: - ANSWER-Directional Stability
This FAA generated document describes the TYPE design and sets forth the limitations
prescribed by the applicable CFR part. - ANSWER-Type Certificate Data Sheet
AnD coRREcTlY WEll DEFInED AnSWERS lATEST 2025 –
2026 AlREADY GRADED A+
The aspect ratio of an aircraft wing is defined as the ratio of the: - ANSWER-Wingspan to the mean
chord.
Which of the following statements concerning density is correct? - ANSWER-If the air pressure is
decreased, the density of the air decreases.
The amount of water vapor present in the air is called: - ANSWER-Humidity
An aircraft's movement around its vertical axis is controlled by the: - ANSWER-Rudder
An aircraft's movement about its lateral axis is controlled by: - ANSWER-Elevators
Which control apparatus is considered to be a secondary flight control? - ANSWER-Trim Tabs
The most common inspection process or procedure which accounts for approximately 80% of all
NDI methods - ANSWER-Visual Inspection
The standard sea level pressure is: - ANSWER-29.92" Hg. at 59 degrees F
Of the three temperature scales, which one is used the least? - ANSWER-Rankine
Which of the following statements is true? - ANSWER-Water vapor weighs 5/8's as much as dry air
, When air holds water vapor, it: - ANSWER-Is lighter than dry air
This inspection method is used to detect surface cracks, pits, subsurface cracks, corrosion on
inner surfaces, and to determine alloy and heat-treat condition: - ANSWER-Eddy Current
This inspection method is a method for detecting cracks, laps, seams, voids, pits, subsurface
holes, and other surface, or slightly subsurface, discontinuities in ferro-magnetic materials: -
ANSWER-Magnetic Particle
A good inspection process to use on nonporous metal and nonmetal components to find
material discontinuities that are open to the surface which may not be evident to normal visual
inspection is: - ANSWER-Dye Penetrant
An NDI inspection technique that uses sound energy moving through the test specimen to
detect flaws is commonly known as: - ANSWER-Ultrasonic Inspection
Tap testing is used to look for which of the following problems: - ANSWER-Delamination of
composite materials
When the weight force is in equilibrium with the lift force, the aircraft: - ANSWER-remains in level
flight
ADs are published to notify aircraft owners and other interested persons of: - ANSWER-Unsafe
conditions which may affect a particular aircraft.
Ailerons control___,Elevators control___,Rudders control____: - ANSWER-Roll; Pitch; Yaw
The purpose of the vertical stabilizer is to provide: - ANSWER-Directional Stability
This FAA generated document describes the TYPE design and sets forth the limitations
prescribed by the applicable CFR part. - ANSWER-Type Certificate Data Sheet
