ASE G1 Test Prep General Automobile Maintenance
Exam Guide 2025-2026
1. Toe can cause tire wear if not within manufacturer's True
specifications
(True or False)
2. Camber can cause tire wear if not within manufactur- True
er's specifications
(True or False)
3. Caster can cause tire wear if not within manufacturer's False
specifications
(True or False)
4. Technician A says that a PAX run-flat tire uses a special Technician A only
wheel.
Technician B says that a standard tire can be used to
replace a PAX run-flat tire.
Which technician is correct ?
5. Wheel back spacing is also called ? Rear spacing
6. A tire is labeled 215/60R15 92T ; the 92 indicates what Load rating
?
7. What do the letter "J J" mean in a wheel designation The shape of the flange
size labeled 14 x 7JJ area
8. A tire is labeled 215/60R15 92T ; the T indicates what ? Speed rating
9. When purchasing replacement tires, do not change 10 mm
tire width from the stock size by more than ?
10. Which type of disc brake caliper may leak brake fluid Fixed disc brake caliper
more often ?
, ASE G1 Test Prep General Automobile Maintenance
Exam Guide 2025-2026
11. Brake fluid boiling point can be measured using ? A Boiling Point Tester
12. What principle is used to create high voltage from low Electromagnetic induction
voltage?
13. The Aspect Ratio of a tire means what ? The ratio of height to
width
14. The pickup coil or trigger is usually electrically con- Ignition Module
nected to the ?
15. Semi-metallic brake pads are made by a process called Sintering
?
16. Which of these takes place during regeneration in a Soot is being burned
Diesel Particulate Filter (DPF)?
17. The brake pad edge code letters "FF" mean what ? Coeflcient of Friction Rat-
ing
18. Engine oil level should be checked .... With the vehicle parked on
level ground
19. A quick-take-up master cylinder is required when Low-Drag caliper
what type of caliper design is used on a vehicle ?
20. What part should be removed to test cylinder com- Glow plug or injector
pression on a diesel engine?
21. Technician A says that maintenance-free batteries use Technician B only
a large amount of water.
Technician B says that maintenance-free batteries use
materials that reduce the amount of water used by the
, ASE G1 Test Prep General Automobile Maintenance
Exam Guide 2025-2026
battery.
Which technician is correct?
22. What part causes the disc brake caliper piston to re- The Square-Cut O-ring
tract when the brakes are released ?
23. Adding a chemical to make ethylene glycol bitter to Embittered
the taste is called ?
24. All safety glasses should meet standards set by ? ANSI (American National
Standards Institute)
25. A potentiometer, a three-wire variable resistor, is used Throttle Position Sensor
in which type of sensor? (TPS)
26. Technician A says that galvanic activity is the result of Technician B only
a poor ground connection.
Technician B says that electrolysis can occur with a
poor ground connection.
Which technician is correct?
27. Where is the fuel-pressure regulator located on a vac- At the outlet of the fuel rail
uum-biased port fuel-injection system?
28. Oil viscosity indicates what ? Tendency of oil to resist
flowing
29. Technician A says that with self-adjusting clutch sys- Technician A only
tems, the release bearing constantly rotates.
Technician B says the ball bearing portion of the re-
lease bearing should be lubricated with high temper-
ature grease during routine maintenance.
Which technician is correct?
Exam Guide 2025-2026
1. Toe can cause tire wear if not within manufacturer's True
specifications
(True or False)
2. Camber can cause tire wear if not within manufactur- True
er's specifications
(True or False)
3. Caster can cause tire wear if not within manufacturer's False
specifications
(True or False)
4. Technician A says that a PAX run-flat tire uses a special Technician A only
wheel.
Technician B says that a standard tire can be used to
replace a PAX run-flat tire.
Which technician is correct ?
5. Wheel back spacing is also called ? Rear spacing
6. A tire is labeled 215/60R15 92T ; the 92 indicates what Load rating
?
7. What do the letter "J J" mean in a wheel designation The shape of the flange
size labeled 14 x 7JJ area
8. A tire is labeled 215/60R15 92T ; the T indicates what ? Speed rating
9. When purchasing replacement tires, do not change 10 mm
tire width from the stock size by more than ?
10. Which type of disc brake caliper may leak brake fluid Fixed disc brake caliper
more often ?
, ASE G1 Test Prep General Automobile Maintenance
Exam Guide 2025-2026
11. Brake fluid boiling point can be measured using ? A Boiling Point Tester
12. What principle is used to create high voltage from low Electromagnetic induction
voltage?
13. The Aspect Ratio of a tire means what ? The ratio of height to
width
14. The pickup coil or trigger is usually electrically con- Ignition Module
nected to the ?
15. Semi-metallic brake pads are made by a process called Sintering
?
16. Which of these takes place during regeneration in a Soot is being burned
Diesel Particulate Filter (DPF)?
17. The brake pad edge code letters "FF" mean what ? Coeflcient of Friction Rat-
ing
18. Engine oil level should be checked .... With the vehicle parked on
level ground
19. A quick-take-up master cylinder is required when Low-Drag caliper
what type of caliper design is used on a vehicle ?
20. What part should be removed to test cylinder com- Glow plug or injector
pression on a diesel engine?
21. Technician A says that maintenance-free batteries use Technician B only
a large amount of water.
Technician B says that maintenance-free batteries use
materials that reduce the amount of water used by the
, ASE G1 Test Prep General Automobile Maintenance
Exam Guide 2025-2026
battery.
Which technician is correct?
22. What part causes the disc brake caliper piston to re- The Square-Cut O-ring
tract when the brakes are released ?
23. Adding a chemical to make ethylene glycol bitter to Embittered
the taste is called ?
24. All safety glasses should meet standards set by ? ANSI (American National
Standards Institute)
25. A potentiometer, a three-wire variable resistor, is used Throttle Position Sensor
in which type of sensor? (TPS)
26. Technician A says that galvanic activity is the result of Technician B only
a poor ground connection.
Technician B says that electrolysis can occur with a
poor ground connection.
Which technician is correct?
27. Where is the fuel-pressure regulator located on a vac- At the outlet of the fuel rail
uum-biased port fuel-injection system?
28. Oil viscosity indicates what ? Tendency of oil to resist
flowing
29. Technician A says that with self-adjusting clutch sys- Technician A only
tems, the release bearing constantly rotates.
Technician B says the ball bearing portion of the re-
lease bearing should be lubricated with high temper-
ature grease during routine maintenance.
Which technician is correct?
