Page 1 of 23
NEIEP 700 FINAL EXAMS (LATEST 2025 UPDATES
STUDY BUNDLE WITH COMPLETE SOLUTIONS)
QUESTIONS AND VERIFIED ANSWERS | 100%
CORRECT | GRADE A
The coil will not pull in despite measuring full line voltage directly
across it. .....ANSWER.....Open Coil
What happens when the switch is closed, then opened?
.....ANSWER.....Relay 1 off-delays, Relay 2 drops immediately
What will normally happen if an unintentional ground is
introduced in a grounded control system? .....ANSWER.....A fuse
will blow
Condition of relays 2F1-3 when the car is traveling up between
the second and third floors. .....ANSWER.....Self Holding
What happens if contact 1F2 7/9 (1F2) fails to close when the
car runs down? .....ANSWER.....The car will not run down
,Page 2 of 23
Which contact(s) change the direction of the door motor when
opening and closing? .....ANSWER.....O1,02,C1, AND C2
What should the stopping distance be if a car speed were 100
FPM? .....ANSWER.....24 inches
What should the stopping distance be if a car speed were 125
FPM? .....ANSWER.....30 inches
What is the function of a retiring cam? .....ANSWER.....Actuate
landing interlocks
What happens when a retiring cam lifts? .....ANSWER.....Locks
Doors
What is the location of the 1F1 4/6 contact? .....ANSWER.....(1
B6)
What is the location of the 1F1 8-9 contact? .....ANSWER.....(2
B2)
, Page 3 of 23
How much dc voltage will a single phase, full-wave rectifier with
134 VAC input produce? .....ANSWER.....120 (134 vac x .9 =
120vdc)
How much dc voltage will a single phase, full-wave rectifier with
240 VAC input produce? .....ANSWER.....216 (240 vac x .9 =
216vdc)
Which contact feeds the in use lights when either the car or a
hoistway door is open? .....ANSWER.....OD 2/8
Which circuit will be affected by the timer's contact if the cam
protection time times out? .....ANSWER.....The Selector circuit
What does the following symbol represent?
.....ANSWER.....Poly/three-phase rectifier
What does the following symbol represent? .....ANSWER.....NC
mechanically operated switch
NEIEP 700 FINAL EXAMS (LATEST 2025 UPDATES
STUDY BUNDLE WITH COMPLETE SOLUTIONS)
QUESTIONS AND VERIFIED ANSWERS | 100%
CORRECT | GRADE A
The coil will not pull in despite measuring full line voltage directly
across it. .....ANSWER.....Open Coil
What happens when the switch is closed, then opened?
.....ANSWER.....Relay 1 off-delays, Relay 2 drops immediately
What will normally happen if an unintentional ground is
introduced in a grounded control system? .....ANSWER.....A fuse
will blow
Condition of relays 2F1-3 when the car is traveling up between
the second and third floors. .....ANSWER.....Self Holding
What happens if contact 1F2 7/9 (1F2) fails to close when the
car runs down? .....ANSWER.....The car will not run down
,Page 2 of 23
Which contact(s) change the direction of the door motor when
opening and closing? .....ANSWER.....O1,02,C1, AND C2
What should the stopping distance be if a car speed were 100
FPM? .....ANSWER.....24 inches
What should the stopping distance be if a car speed were 125
FPM? .....ANSWER.....30 inches
What is the function of a retiring cam? .....ANSWER.....Actuate
landing interlocks
What happens when a retiring cam lifts? .....ANSWER.....Locks
Doors
What is the location of the 1F1 4/6 contact? .....ANSWER.....(1
B6)
What is the location of the 1F1 8-9 contact? .....ANSWER.....(2
B2)
, Page 3 of 23
How much dc voltage will a single phase, full-wave rectifier with
134 VAC input produce? .....ANSWER.....120 (134 vac x .9 =
120vdc)
How much dc voltage will a single phase, full-wave rectifier with
240 VAC input produce? .....ANSWER.....216 (240 vac x .9 =
216vdc)
Which contact feeds the in use lights when either the car or a
hoistway door is open? .....ANSWER.....OD 2/8
Which circuit will be affected by the timer's contact if the cam
protection time times out? .....ANSWER.....The Selector circuit
What does the following symbol represent?
.....ANSWER.....Poly/three-phase rectifier
What does the following symbol represent? .....ANSWER.....NC
mechanically operated switch
