TTT1 Study guide Exam Questions & Answers Latest Update
TTT1 Study guide Exam Questions & Answers
Latest Update
Who is the third-party group that approves and endorses standards? - ✔-American National Standards
Institute
What term is used to describe the documents written by members, or peers, in the industry? - ✔-
Standards
A company's health, safety and environment policy should be a combination of labor regulations and ? -
✔-Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts general
clause? - ✔-Employer
On a job site who should be involved in the JHA process? - ✔-The Whole Crew
What does the Term SOW stand for? - ✔-Scope Of Work
The letters JHA stand for what ? - ✔-Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? - ✔-3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall does the
case need to by to have the correct slope? - ✔-4
Work boots with ankle support are recommended for all work sites? - ✔-True
What do the letters PPE stand for ? - ✔-Personal Protective Equipment
TTT1 Study guide Exam Questions & Answers Latest Update
, TTT1 Study guide Exam Questions & Answers Latest Update
What does the ground fault circuit interrupter (GFCI) do? - ✔-Senses a short circuit, prevents
electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ✔-Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to your
anchorage be placed?extend? - ✔-Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? - ✔-Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? - ✔-Four feey
What is the minimum force that a work positioning system anchorage must be able to withstand? - ✔-
Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection use? - ✔-
5,000 lbs
When working, how often should fall protection equipment be inspected ? - ✔-Daily before each use
According to the applicable industry standard, what is the minimum height from a lower surface or
ground where fall protection must be used? - ✔-Six feet
How many pounds force is one kilo Newton(kN) - ✔-225
What are the four most common types of towers used to support telecommunications antennas? - ✔-
Guyed towers, self-support towers, monopoles, and non- standard
What identifies a self-support tower? - ✔-Horizontal member
TTT1 Study guide Exam Questions & Answers Latest Update
TTT1 Study guide Exam Questions & Answers
Latest Update
Who is the third-party group that approves and endorses standards? - ✔-American National Standards
Institute
What term is used to describe the documents written by members, or peers, in the industry? - ✔-
Standards
A company's health, safety and environment policy should be a combination of labor regulations and ? -
✔-Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts general
clause? - ✔-Employer
On a job site who should be involved in the JHA process? - ✔-The Whole Crew
What does the Term SOW stand for? - ✔-Scope Of Work
The letters JHA stand for what ? - ✔-Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? - ✔-3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall does the
case need to by to have the correct slope? - ✔-4
Work boots with ankle support are recommended for all work sites? - ✔-True
What do the letters PPE stand for ? - ✔-Personal Protective Equipment
TTT1 Study guide Exam Questions & Answers Latest Update
, TTT1 Study guide Exam Questions & Answers Latest Update
What does the ground fault circuit interrupter (GFCI) do? - ✔-Senses a short circuit, prevents
electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ✔-Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to your
anchorage be placed?extend? - ✔-Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? - ✔-Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? - ✔-Four feey
What is the minimum force that a work positioning system anchorage must be able to withstand? - ✔-
Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection use? - ✔-
5,000 lbs
When working, how often should fall protection equipment be inspected ? - ✔-Daily before each use
According to the applicable industry standard, what is the minimum height from a lower surface or
ground where fall protection must be used? - ✔-Six feet
How many pounds force is one kilo Newton(kN) - ✔-225
What are the four most common types of towers used to support telecommunications antennas? - ✔-
Guyed towers, self-support towers, monopoles, and non- standard
What identifies a self-support tower? - ✔-Horizontal member
TTT1 Study guide Exam Questions & Answers Latest Update
