1
For Expert help and assignment solutions, +254707240657
Gas Technician 2 Exam Questions and
Answers (100% Correct Answers) Already
Graded A+
Fuses serving motor circuits should be:
a) Quick blow type
b) Time delay type
© 2025 Assignment Expert
c) Oversized by 2.5%
d) Oversized by 3.5% [ ANS: ] b) Time delay type.
Guru01 - Stuvia
As the length of on elecincal run increases, it may be necessary
to;
a) increase the wire size,
b) Use a dilerent moe o, conducior
c)Decreose the use size
d) increase the fuse size [ ANS: ] a) Increase the wire size
6. Millivolt wiring should be isolated from line voliage wiring
because:
a) The line voltage wire will overheat the low voltage wiring.
b) The resistance of the millivolt wiring will be increased.
, 2
For Expert help and assignment solutions, +254707240657
c)The current in the low voltage wire will be reduced to that of the
millivolt wire,
d) The line vollage will induce a volioge into the millivolt wiring [
ANS: ] d) The line vollage will induce a volioge into the millivolt
wiring
7. Which tool is used to determine if the windings on on electric
motor have shorted?
a) Voltmeter
© 2025 Assignment Expert
b) Ammeter
c) Ohmmeter
Guru01 - Stuvia
d) Wattmeter [ ANS: ] c) Ohmmeter
8. On on electrical schematic diagram, the safety controls are
typically drawn;
a) To the right of the loads.
b) Above Ihe loads
c)Below the loads
d) To the left of the loads [ ANS: ] d) To the left of the loads
9. Which of the following types of wire must be used in damp
locations?
a) NMD
b) NNW
, 3
For Expert help and assignment solutions, +254707240657
c) LVT
d) BX [ ANS: ] b) NMW
10. On an electrical schematic, all operating controls ore drown:
o) In their energized positions.
b) in their de-energized positions,
c) Normally closed,
© 2025 Assignment Expert
d) Normally open. [ ANS: ] d) Normally open
11. An inline ammeter is connected:
Guru01 - Stuvia
a) In series with the device being checked.
b) In porallel with the device being checked.
c) With the system power off
d) Across the load. [ ANS: ] a) In series with the device being
checked
12. As the length of a conductor increases, the voltage drop
along the conductor:
a) Increases
b) Decreases.
c) Remains the same
d) Should be as flexiole as possible [ ANS: ] a) Increases
For Expert help and assignment solutions, +254707240657
Gas Technician 2 Exam Questions and
Answers (100% Correct Answers) Already
Graded A+
Fuses serving motor circuits should be:
a) Quick blow type
b) Time delay type
© 2025 Assignment Expert
c) Oversized by 2.5%
d) Oversized by 3.5% [ ANS: ] b) Time delay type.
Guru01 - Stuvia
As the length of on elecincal run increases, it may be necessary
to;
a) increase the wire size,
b) Use a dilerent moe o, conducior
c)Decreose the use size
d) increase the fuse size [ ANS: ] a) Increase the wire size
6. Millivolt wiring should be isolated from line voliage wiring
because:
a) The line voltage wire will overheat the low voltage wiring.
b) The resistance of the millivolt wiring will be increased.
, 2
For Expert help and assignment solutions, +254707240657
c)The current in the low voltage wire will be reduced to that of the
millivolt wire,
d) The line vollage will induce a volioge into the millivolt wiring [
ANS: ] d) The line vollage will induce a volioge into the millivolt
wiring
7. Which tool is used to determine if the windings on on electric
motor have shorted?
a) Voltmeter
© 2025 Assignment Expert
b) Ammeter
c) Ohmmeter
Guru01 - Stuvia
d) Wattmeter [ ANS: ] c) Ohmmeter
8. On on electrical schematic diagram, the safety controls are
typically drawn;
a) To the right of the loads.
b) Above Ihe loads
c)Below the loads
d) To the left of the loads [ ANS: ] d) To the left of the loads
9. Which of the following types of wire must be used in damp
locations?
a) NMD
b) NNW
, 3
For Expert help and assignment solutions, +254707240657
c) LVT
d) BX [ ANS: ] b) NMW
10. On an electrical schematic, all operating controls ore drown:
o) In their energized positions.
b) in their de-energized positions,
c) Normally closed,
© 2025 Assignment Expert
d) Normally open. [ ANS: ] d) Normally open
11. An inline ammeter is connected:
Guru01 - Stuvia
a) In series with the device being checked.
b) In porallel with the device being checked.
c) With the system power off
d) Across the load. [ ANS: ] a) In series with the device being
checked
12. As the length of a conductor increases, the voltage drop
along the conductor:
a) Increases
b) Decreases.
c) Remains the same
d) Should be as flexiole as possible [ ANS: ] a) Increases
