Vol4
1. (601) The vehicle frame and body are combined together as a unit in a.
a. mono frame. B. unitized body. c. integral frame. d. three-rail body. - ANS-B. unitized body.
2. (601) What type of frame misalignment do you have if the cross members no longer form right
angles with the side rails?
a. Zig. b. Sag. c. Sway. D. Diamond. - ANS-D
3. (601) If you do not have specialized measuring equipment determining frame misalignment,
what other method are you using if you transfer checkpoints to a level floor?
a. String and pencil. b. Bubble level. c. Pitted level. D. Plumb bob - ANS-D
4. (602) What auto body shape has the appearance of a curved surface?
A.Crown. b. Round. c. Bend. d. Arc. - ANS-A
5. (002) What auto body curved type has lower door panels, hoods, and deck lids?
a. High-crown. B. low-crown. c. High bend. d. Low bend. - ANS-B.Low crown
6. (602) The auto body curved surface around the taillights and headlights is usually a
a. low bend. b. low-crown. c, high-crown. reverse crown. - ANS-D. reverse crown
7. (603) Which is normally the heaviest and largest auto body repair hammer?
A. Bumping. B. Gouging. c. Dinging. d. Picking. - ANS-A. Bumping
8. (603) If you need to repair a panel that is hard to get to, which auto body repair hammer do
you use?
a. Ball-peen. b. Bumping. c. Dinging. D. Pick. - ANS-D. Pick
9. (604) What auto body repair tool do you hold against the inside of the body panel as a
backup tool when using a hammer?
a. Dolly block. b. Impact block. c. Dinging hammer. d. Bumping hammer. - ANS-A. Dolly block
10. (604) What type of dolly block working face do you use if you want increased metal
stretching and increased lift of the damaged metal surface?
a. Contact crown. b. Impact crown. EHigh-crown. d. Low-crown. - ANS-C. high crown
11. (605) When making auto body repairs with a bumping spoon, where do you place the spoon
in relationship to the metal surface?
A. On the other side of the metal surface from the hammer side
, B. Between the metal surface and the hammer.
, c. To the right of the body panel damage.
d. To the left of the body panel damage. - ANS-B
12. (605) Which spoon would you use as a pry tool for repairing body damage?
a. Caulking. b. Bumping. c.Body. d. Low. - ANS-C
13. (606) What do you call the damage to the auto body panel where there is an increase in
surface area?
a. Bend. B. Stretch. c. Distortion. d. Displacement. - ANS-B
14. (606) When removing distortions from a damaged auto body metal surface, you should start
with the
a. first distortion to occur. B. blast distortion to occur. c. center point of impact. d. deepest impact
point. - ANS-B
15. (607) After you inspect and analyze the body damage, your next step in body and fender
repair is to perform metal
A. bumping. b. roughing. c. grinding. d. cutting. - ANS-A
16. During your auto body repairs, it is important to carefully lower the raised metal first because
it.
A. Increases the chances of buckling B. Is the only surface you can get to first C. Reduces the
chances of shrinking and large bends of metal. D. Reduces the chances of stretches and sharp
bends of metal. - ANS-D
17. (607) The auto body repair process where you release a stretched area with a cross-peen
hammer and a specialized dolly is called?
a. automatic b. hand shrinking. stretching. c. cold stretching. D. cold shrinking. - ANS-D
18. (608) What two methods can you use to straighten a deck lid?
A. Manually and hydraulically b.Hydraulically and pneumatically. c. Manually and with a
hydraulic wedge. d. Hydraulically and with a hammer and a wood block - ANS-A
19. (609) When you need to use plastic fillers, what two items will you mix? a. Plastic base and
adhesion promoter. b. Resin base and a catalyst. C. Plastic powder and resin. d. Catalyst and
plastic gel. - ANS-B
20. (610) If you mix a catalyst and a promoter together to repair fiberglass, the mixture will a.
harden. B. explode. c. not react. d. evaporate. - ANS-B
21. (611) When glass is subject to temperature changes, allowances must be made for
a. its tendency to shatter at temperatures above 150° F. b. its tendency to crack at temperatures
above 150° F. c. the impact of oncoming ambient air. d. expansion and contraction. - ANS-D
1. (601) The vehicle frame and body are combined together as a unit in a.
a. mono frame. B. unitized body. c. integral frame. d. three-rail body. - ANS-B. unitized body.
2. (601) What type of frame misalignment do you have if the cross members no longer form right
angles with the side rails?
a. Zig. b. Sag. c. Sway. D. Diamond. - ANS-D
3. (601) If you do not have specialized measuring equipment determining frame misalignment,
what other method are you using if you transfer checkpoints to a level floor?
a. String and pencil. b. Bubble level. c. Pitted level. D. Plumb bob - ANS-D
4. (602) What auto body shape has the appearance of a curved surface?
A.Crown. b. Round. c. Bend. d. Arc. - ANS-A
5. (002) What auto body curved type has lower door panels, hoods, and deck lids?
a. High-crown. B. low-crown. c. High bend. d. Low bend. - ANS-B.Low crown
6. (602) The auto body curved surface around the taillights and headlights is usually a
a. low bend. b. low-crown. c, high-crown. reverse crown. - ANS-D. reverse crown
7. (603) Which is normally the heaviest and largest auto body repair hammer?
A. Bumping. B. Gouging. c. Dinging. d. Picking. - ANS-A. Bumping
8. (603) If you need to repair a panel that is hard to get to, which auto body repair hammer do
you use?
a. Ball-peen. b. Bumping. c. Dinging. D. Pick. - ANS-D. Pick
9. (604) What auto body repair tool do you hold against the inside of the body panel as a
backup tool when using a hammer?
a. Dolly block. b. Impact block. c. Dinging hammer. d. Bumping hammer. - ANS-A. Dolly block
10. (604) What type of dolly block working face do you use if you want increased metal
stretching and increased lift of the damaged metal surface?
a. Contact crown. b. Impact crown. EHigh-crown. d. Low-crown. - ANS-C. high crown
11. (605) When making auto body repairs with a bumping spoon, where do you place the spoon
in relationship to the metal surface?
A. On the other side of the metal surface from the hammer side
, B. Between the metal surface and the hammer.
, c. To the right of the body panel damage.
d. To the left of the body panel damage. - ANS-B
12. (605) Which spoon would you use as a pry tool for repairing body damage?
a. Caulking. b. Bumping. c.Body. d. Low. - ANS-C
13. (606) What do you call the damage to the auto body panel where there is an increase in
surface area?
a. Bend. B. Stretch. c. Distortion. d. Displacement. - ANS-B
14. (606) When removing distortions from a damaged auto body metal surface, you should start
with the
a. first distortion to occur. B. blast distortion to occur. c. center point of impact. d. deepest impact
point. - ANS-B
15. (607) After you inspect and analyze the body damage, your next step in body and fender
repair is to perform metal
A. bumping. b. roughing. c. grinding. d. cutting. - ANS-A
16. During your auto body repairs, it is important to carefully lower the raised metal first because
it.
A. Increases the chances of buckling B. Is the only surface you can get to first C. Reduces the
chances of shrinking and large bends of metal. D. Reduces the chances of stretches and sharp
bends of metal. - ANS-D
17. (607) The auto body repair process where you release a stretched area with a cross-peen
hammer and a specialized dolly is called?
a. automatic b. hand shrinking. stretching. c. cold stretching. D. cold shrinking. - ANS-D
18. (608) What two methods can you use to straighten a deck lid?
A. Manually and hydraulically b.Hydraulically and pneumatically. c. Manually and with a
hydraulic wedge. d. Hydraulically and with a hammer and a wood block - ANS-A
19. (609) When you need to use plastic fillers, what two items will you mix? a. Plastic base and
adhesion promoter. b. Resin base and a catalyst. C. Plastic powder and resin. d. Catalyst and
plastic gel. - ANS-B
20. (610) If you mix a catalyst and a promoter together to repair fiberglass, the mixture will a.
harden. B. explode. c. not react. d. evaporate. - ANS-B
21. (611) When glass is subject to temperature changes, allowances must be made for
a. its tendency to shatter at temperatures above 150° F. b. its tendency to crack at temperatures
above 150° F. c. the impact of oncoming ambient air. d. expansion and contraction. - ANS-D
