PEARSON EDEXCEL
2024
2024
PEARSON
Edexcel
,Pearson Edexcel Level 1/Level 2 GCSE (9–1)
1DT0/1A
Design and Technology
COMPONENT 1: Metals
Mark Scheme Plus
Question Paper
Merged
, Please check the examination details below before entering your candidate information
Candidate surname Other names
Centre Number Candidate Number
Pearson Edexcel Level 1/Level 2 GCSE (9–1)
Tuesday 18 June 2024
Morning (Time: 1 hour 45 minutes)
Paper
reference 1DT0/1A
Design and Technology � �
COMPONENT 1: Metals
You must have: Total Marks
Calculator, ruler, HB pencil, protractor, pair of compasses
Instructions
•• Use black ink or ball-point pen.
Fill in the boxes at the top of this page with your name,
centre number and candidate number.
•• Answer all questions.
Answer the questions in the spaces provided
– there may be more space than you need.
••
Calculators may be used.
Any diagrams may NOT be accurately drawn, unless otherwise indicated.
• You endshow
must
at the all your
of your working out with your answer clearly identified
solution.
Information
•• The total mark for this paper is 100.
The marks for each question are shown in brackets
– use this as a guide as to how much time to spend on each question.
Advice
• Read each question carefully before you start to answer it.
• Try to answer every question.
• Check your answers if you have time at the end.
Turn over
P74047A
©2024 Pearson Education Ltd.
F:1/1/1/1/1/1/1/1/1
, SECTION A
Core
DO NOT WRITE IN THIS AREA
Answer ALL questions. Write your answers in the spaces provided.
1 (a) The materials that products are made from are chosen because of their
properties.
Figure 1 shows a table of products.
For each of the products shown, give a property of the material it is made from
that makes the material suitable for the product.
The first one has been done for you.
Picture of product Material and product Property
Cast iron frying pan Hard
DO NOT WRITE IN THIS AREA
(1)
Cotton bath towel
(i) . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .. . . .. . .. . .. . .. . .. . .
(1)
Polyester resin earrings
(ii) . . . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .. . .. .. . .. ... . .. . .. .. . .. .. . .. .. . .
(1)
DO NOT WRITE IN THIS AREA
Copier paper
(iii) . . . . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. . .. .. . .. .. . .. .. . .. .
(1)
Beech cooking spoon
(iv) . . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .. . .. .. . .. .. . .. .. .. . .. . .. .. . .. .. . .. .. . .. .
Figure 1
2
����
2024
2024
PEARSON
Edexcel
,Pearson Edexcel Level 1/Level 2 GCSE (9–1)
1DT0/1A
Design and Technology
COMPONENT 1: Metals
Mark Scheme Plus
Question Paper
Merged
, Please check the examination details below before entering your candidate information
Candidate surname Other names
Centre Number Candidate Number
Pearson Edexcel Level 1/Level 2 GCSE (9–1)
Tuesday 18 June 2024
Morning (Time: 1 hour 45 minutes)
Paper
reference 1DT0/1A
Design and Technology � �
COMPONENT 1: Metals
You must have: Total Marks
Calculator, ruler, HB pencil, protractor, pair of compasses
Instructions
•• Use black ink or ball-point pen.
Fill in the boxes at the top of this page with your name,
centre number and candidate number.
•• Answer all questions.
Answer the questions in the spaces provided
– there may be more space than you need.
••
Calculators may be used.
Any diagrams may NOT be accurately drawn, unless otherwise indicated.
• You endshow
must
at the all your
of your working out with your answer clearly identified
solution.
Information
•• The total mark for this paper is 100.
The marks for each question are shown in brackets
– use this as a guide as to how much time to spend on each question.
Advice
• Read each question carefully before you start to answer it.
• Try to answer every question.
• Check your answers if you have time at the end.
Turn over
P74047A
©2024 Pearson Education Ltd.
F:1/1/1/1/1/1/1/1/1
, SECTION A
Core
DO NOT WRITE IN THIS AREA
Answer ALL questions. Write your answers in the spaces provided.
1 (a) The materials that products are made from are chosen because of their
properties.
Figure 1 shows a table of products.
For each of the products shown, give a property of the material it is made from
that makes the material suitable for the product.
The first one has been done for you.
Picture of product Material and product Property
Cast iron frying pan Hard
DO NOT WRITE IN THIS AREA
(1)
Cotton bath towel
(i) . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .. . . .. . .. . .. . .. . .. . .
(1)
Polyester resin earrings
(ii) . . . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .. . .. .. . .. ... . .. . .. .. . .. .. . .. .. . .
(1)
DO NOT WRITE IN THIS AREA
Copier paper
(iii) . . . . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. . .. .. . .. .. . .. .. . .. .
(1)
Beech cooking spoon
(iv) . . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .. . .. .. . .. .. . .. .. .. . .. . .. .. . .. .. . .. .. . .. .
Figure 1
2
����
