Oregon Tattoo Questions With Solutions
buzz or rattle do not allow the front spring to hang over the rear of the armature bar
because it can create a ______ or ___________
contact screws there should be no sharp edges on __________ _______, should be
rounded and very smooth
faster a short front spring will be _________
rockwell scale all metals are measured on the _________ _______
48-51 best on the scale for spring stock is ___-___
alcohol can be used to clean your contact area and screws and spring
rattle thin, cheap binding posts cause ________
leverage _____________ is a key factor when it comes to a-bar choice
, Oregon Tattoo Questions With Solutions
100 copper is ___% conductive
copper and zinc brass is a mixture of
6-32, 8-32 some machines have _-__ threaded machine screws and some have _-__
thicker binding posts _________ __________ ______ help dampen vibrations
shorter is a shorter or longer front spring better on a liner?
shoulder washers screw insulators commonly known as __________ __________ , most
common are made of fiber and plastic
true a longer A-Bar has more leverage, true or false?
electrical contact to contact screw purpose of the binding post
, Oregon Tattoo Questions With Solutions
rubber grommets dampener or rubber grommets better?
hot never use brass screws or any other non-ferrous screws for the coil screws can cause
the coils to get ___
soldering lugs ______________ ____ are soldered at the ends of the coil wires and
capacitor wires, with a 5/16" tube vise
liners tattoo machine capacitors have 22 MFD for ________
shaders tattoo machine capacitors have 47 MFD for _________
faster the lower the MFD rating the ________ the machine will run
frame which parts job is to simply "hold" the circuits in place
3 how many circuits when you look at the machine unit?
, Oregon Tattoo Questions With Solutions
12 most machines run well under __ volts
25 how many volts for 47 MFD?
coils the "heart and brains" of the tattoo machine
5/16, 3/8 standard coils are 1.25 inches tall and vary in diameter but most common are
_/__ and _/_
coils if you have a noisy machine and can't find a reason check the _____
skin scribe a special marker for drawing on skin freehand
capacitor a device used to store an electric charge, consisting of one or more pairs of
conductors separated by an insulator.
buzz or rattle do not allow the front spring to hang over the rear of the armature bar
because it can create a ______ or ___________
contact screws there should be no sharp edges on __________ _______, should be
rounded and very smooth
faster a short front spring will be _________
rockwell scale all metals are measured on the _________ _______
48-51 best on the scale for spring stock is ___-___
alcohol can be used to clean your contact area and screws and spring
rattle thin, cheap binding posts cause ________
leverage _____________ is a key factor when it comes to a-bar choice
, Oregon Tattoo Questions With Solutions
100 copper is ___% conductive
copper and zinc brass is a mixture of
6-32, 8-32 some machines have _-__ threaded machine screws and some have _-__
thicker binding posts _________ __________ ______ help dampen vibrations
shorter is a shorter or longer front spring better on a liner?
shoulder washers screw insulators commonly known as __________ __________ , most
common are made of fiber and plastic
true a longer A-Bar has more leverage, true or false?
electrical contact to contact screw purpose of the binding post
, Oregon Tattoo Questions With Solutions
rubber grommets dampener or rubber grommets better?
hot never use brass screws or any other non-ferrous screws for the coil screws can cause
the coils to get ___
soldering lugs ______________ ____ are soldered at the ends of the coil wires and
capacitor wires, with a 5/16" tube vise
liners tattoo machine capacitors have 22 MFD for ________
shaders tattoo machine capacitors have 47 MFD for _________
faster the lower the MFD rating the ________ the machine will run
frame which parts job is to simply "hold" the circuits in place
3 how many circuits when you look at the machine unit?
, Oregon Tattoo Questions With Solutions
12 most machines run well under __ volts
25 how many volts for 47 MFD?
coils the "heart and brains" of the tattoo machine
5/16, 3/8 standard coils are 1.25 inches tall and vary in diameter but most common are
_/__ and _/_
coils if you have a noisy machine and can't find a reason check the _____
skin scribe a special marker for drawing on skin freehand
capacitor a device used to store an electric charge, consisting of one or more pairs of
conductors separated by an insulator.
