ASE MLR Certification Test(Latest Exam
2024)
Both A and B - correct answers✅Technician observes that the brake fluid level is
at the "Min" mark in the master cylinder reservoir. Tech A says that worn front pads
could be the cause. Tech B says that a leak in the brake hydraulic system could be
the cause. Who is right?
A only - correct answers✅The tires of a vehicle are being rotated and balanced.
Tech A says that the wheel weight retaining clips must be matched to the rim
profile. Tech B says that directional tires are rotated in a criss-cross pattern. Who is
right?
Safely exit the building - correct answers✅When a shop fire cannot be
immediately contained, the best thing to do is warn others in the area, and:
300 amps for 15 seconds - correct answers✅A fully charged battery rated at 600
CCA, the ambient temperature is 70 degrees which of these current and time
periods should be used?
B only - correct answers✅A vehicle's halogen headlamp bulbs are being replaced.
Technician A says the glass part of the bulb can only be handled with bare hands.
Technician B says the headlamp may need to be removed. Who is right?
0.728 - correct answers✅On a Metric Micrometer upper sleeve reading 5.0mm
with lower sleeve reading 0.50mm and a thimble reading of 0.01mm what is the
overall reading?
A only - correct answers✅The fuel filter on a fuel-injected vehicle is being
replaced. Tech A says the fuel pressure should be relieved before removing the filter.
Tech B says that the arrow on the fuel filter should point towards the fuel tank. Who
is right?
The brake pedal feels low and spongy - correct answers✅Which of these is an
indication of air in the brake hydraulic system?
Anaerobic - correct answers✅Which of these cures in the absence of air?
, ASE MLR Certification Test(Latest Exam
2024)
Fluid contaminated brake linings - correct answers✅A grabbing brake condition
can be caused by any of these EXCEPT:
Visually verify that the oil filter gasket is properly installed - correct
answers✅When performing an oil filter change on a vehicle with a spin on oil filter,
the technician must:
Voltage regulation - correct answers✅A vehicle's battery prematurely fails. A
charging system output test shows the generator (alternator) is producing a
constant 16.0 volts. This could indicate a failed:
Seal should be lubricated with transmission fluid - correct answers✅A
transmission equipped with a filter is being serviced. When installing the new filter,
the:
Both A and B - correct answers✅While inspecting the rear axle wheel studs on a
rear-wheel drive vehicle, the technician observed that one stud is damaged.
Technician A says that all the wheel studs on the hub assembly should be replaced.
Technician B says that the thread pitch and diameter of the replacement stud must
be the same as the original. Who is right?
Neither A nor B - correct answers✅The three C's (concern, cause, and correction)
are being reviewed on the repair order. Technician A says that the customer's
statement that the steering wheel shakes is the "correction". Technician B says that
a customer's statement about a puddle on the floor of the customer's garage is the
"cause".
Pump the brake pedal until firm - correct answers✅A technician installs new
brake pads on the front of a vehicle. Before the vehicle is removed from the lift the
technician should:
Determine rotor minimum "machine to" thickness - correct answers✅When
measuring parallelism of a disc brake rotor, a technician measures 0.002" variation
beyond specifications. The next step is to:
2024)
Both A and B - correct answers✅Technician observes that the brake fluid level is
at the "Min" mark in the master cylinder reservoir. Tech A says that worn front pads
could be the cause. Tech B says that a leak in the brake hydraulic system could be
the cause. Who is right?
A only - correct answers✅The tires of a vehicle are being rotated and balanced.
Tech A says that the wheel weight retaining clips must be matched to the rim
profile. Tech B says that directional tires are rotated in a criss-cross pattern. Who is
right?
Safely exit the building - correct answers✅When a shop fire cannot be
immediately contained, the best thing to do is warn others in the area, and:
300 amps for 15 seconds - correct answers✅A fully charged battery rated at 600
CCA, the ambient temperature is 70 degrees which of these current and time
periods should be used?
B only - correct answers✅A vehicle's halogen headlamp bulbs are being replaced.
Technician A says the glass part of the bulb can only be handled with bare hands.
Technician B says the headlamp may need to be removed. Who is right?
0.728 - correct answers✅On a Metric Micrometer upper sleeve reading 5.0mm
with lower sleeve reading 0.50mm and a thimble reading of 0.01mm what is the
overall reading?
A only - correct answers✅The fuel filter on a fuel-injected vehicle is being
replaced. Tech A says the fuel pressure should be relieved before removing the filter.
Tech B says that the arrow on the fuel filter should point towards the fuel tank. Who
is right?
The brake pedal feels low and spongy - correct answers✅Which of these is an
indication of air in the brake hydraulic system?
Anaerobic - correct answers✅Which of these cures in the absence of air?
, ASE MLR Certification Test(Latest Exam
2024)
Fluid contaminated brake linings - correct answers✅A grabbing brake condition
can be caused by any of these EXCEPT:
Visually verify that the oil filter gasket is properly installed - correct
answers✅When performing an oil filter change on a vehicle with a spin on oil filter,
the technician must:
Voltage regulation - correct answers✅A vehicle's battery prematurely fails. A
charging system output test shows the generator (alternator) is producing a
constant 16.0 volts. This could indicate a failed:
Seal should be lubricated with transmission fluid - correct answers✅A
transmission equipped with a filter is being serviced. When installing the new filter,
the:
Both A and B - correct answers✅While inspecting the rear axle wheel studs on a
rear-wheel drive vehicle, the technician observed that one stud is damaged.
Technician A says that all the wheel studs on the hub assembly should be replaced.
Technician B says that the thread pitch and diameter of the replacement stud must
be the same as the original. Who is right?
Neither A nor B - correct answers✅The three C's (concern, cause, and correction)
are being reviewed on the repair order. Technician A says that the customer's
statement that the steering wheel shakes is the "correction". Technician B says that
a customer's statement about a puddle on the floor of the customer's garage is the
"cause".
Pump the brake pedal until firm - correct answers✅A technician installs new
brake pads on the front of a vehicle. Before the vehicle is removed from the lift the
technician should:
Determine rotor minimum "machine to" thickness - correct answers✅When
measuring parallelism of a disc brake rotor, a technician measures 0.002" variation
beyond specifications. The next step is to:
