Chapter 8: Dynamic Host Configuration
Protocol (DHCP) (Net Accad) (Exam)
An administrator issues the commands:
Router(config)# interface g0/1
Router(config-if)# ip address dhcp
What is the administrator trying to achieve?
configuring the router to act as a DHCPv4 server
configuring the router to resolve IP address conflicts
configuring the router to act as a relay agent
configuring the router to obtain IP parameters from a DHCPv4 server - correct answer ✔✔configuring
the router to obtain IP parameters from a DHCPv4 server
(corrected)
The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients
being 0
X-The GigabitEthernet interface is not activated. - correct answer ✔✔Refer to the exhibit. A network
administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring
IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain
name information configured in the DHCP pool. What could be the cause of the problem?
, The router is configured for SLAAC operation.
The GigabitEthernet interface is not activated.
The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients
being 0.
The DNS server address is not on the same network as the clients are on.
A company implements the stateless DHCPv6 method for configuring IPv6 addresses on employee
workstations. After a workstation receives messages from multiple DHCPv6 servers to indicate their
availability for DHCPv6 service, which message does it send to a server for configuration information?
DHCPv6 SOLICIT
DHCPv6 REQUEST
DHCPv6 INFORMATION-REQUEST
DHCPv6 ADVERTISE - correct answer ✔✔DHCPv6 INFORMATION-REQUEST
Under which two circumstances would a router usually be configured as a DHCPv4 client? (Choose two.)
The router has a fixed IP address.
The router is intended to be used as a SOHO gateway.
The router is meant to provide IP addresses to the hosts.
This is an ISP requirement.
Protocol (DHCP) (Net Accad) (Exam)
An administrator issues the commands:
Router(config)# interface g0/1
Router(config-if)# ip address dhcp
What is the administrator trying to achieve?
configuring the router to act as a DHCPv4 server
configuring the router to resolve IP address conflicts
configuring the router to act as a relay agent
configuring the router to obtain IP parameters from a DHCPv4 server - correct answer ✔✔configuring
the router to obtain IP parameters from a DHCPv4 server
(corrected)
The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients
being 0
X-The GigabitEthernet interface is not activated. - correct answer ✔✔Refer to the exhibit. A network
administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring
IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain
name information configured in the DHCP pool. What could be the cause of the problem?
, The router is configured for SLAAC operation.
The GigabitEthernet interface is not activated.
The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients
being 0.
The DNS server address is not on the same network as the clients are on.
A company implements the stateless DHCPv6 method for configuring IPv6 addresses on employee
workstations. After a workstation receives messages from multiple DHCPv6 servers to indicate their
availability for DHCPv6 service, which message does it send to a server for configuration information?
DHCPv6 SOLICIT
DHCPv6 REQUEST
DHCPv6 INFORMATION-REQUEST
DHCPv6 ADVERTISE - correct answer ✔✔DHCPv6 INFORMATION-REQUEST
Under which two circumstances would a router usually be configured as a DHCPv4 client? (Choose two.)
The router has a fixed IP address.
The router is intended to be used as a SOHO gateway.
The router is meant to provide IP addresses to the hosts.
This is an ISP requirement.
