EG-165/EGA113 Design Project 1 – Pull rod and push rod - Report
Group members student numbers (list in numerical order)
993478 911563 990423
Group members
Names
Jase White Louis Ratti Daniel Fraser
Tick as
Checklist
Required
All student numbers on all sheets
This sheet complete
Assembly Drawing, pull and push rod, including section through centre
Insert manufacturing drawing
How to hand in your project:
Create pdf files of this document and your drawings. Post these on blackboard.
Remember this is a group project where all group members will be given the same mark. All work,
including drawings and calculations should be different from other groups. Groups submitting very
similar drawings will be reported to the College Unfair Practice process.
EG-165 Design Project 1 – Pull rod and push rod - FEEDBACK
Levels of Achievement
Criteria Novice Competent Proficient Excellent
2 Points 3 Points 4 Points 5 Points
Calculations
Incomplete Significant Errors Minor Errors Accurate
5 Points
2 Points 3 Points 4 Points
Perfectly laid out and
Drawing below Average drawing, Good tidy
dimensioned drawing.
Assembly standard. Doesn't slightly untidy. drawing.
Components perfectly
Drawings fit. Structurally Reasonable design. Competent design
sized. Assembly
Weak. Essential Some omissions of with all features
method and alignment
items missing. detailing. included.
good.
Insert 3 Points 4 Points
2 Points 5 Points
Manufacturing Not possible to Competent with
Below Standard Perfect for manufacture
Drawing manufacture from minor errors
4 Points
2 Points 3 Points 5 Points
Weight Competitive
Above 220g Between 170-220g Lowest Weight Group
below 170g
, Specification Pull Rod Push Rod
Material Choice (Include Aluminium 6082T6 Aluminium 6082T6
specific alloy details)
Material yield stress (MPa) 310 310
Material Young’s Modulus 70 70
(GPa)
Outside Diameter (mm) 12.7 12.7
Inside Diameter (mm) 9.449 9.449
Wall Thickness (mm) 3.251 3.251
Input load (N) 1751.26835 1751.26835
Stress in tension (MPa) 30.9664717
Maximum buckling limit (N) 5201.146
Stress in bolt 2 (MPa) 40.4496 40.4496
Rod end manufacturer and part Aurora AM-M5 rod end Aurora AM-M5 rod end
number (Right Hand thread) bearing bearing
Rod end manufacturer and part Aurora AM-M5 rod end Aurora AM-M5 rod end
number (Left Hand thread) bearing bearing
Weights
Bar/tube (g) 61 61
Two inserts (g) 10 10
Two Rod Ends (g) 131 13
Total weight of 1x pull rod assembly +1x push rod assembly (g) 168
Group members student numbers (list in numerical order)
993478 911563 990423
Group members
Names
Jase White Louis Ratti Daniel Fraser
Tick as
Checklist
Required
All student numbers on all sheets
This sheet complete
Assembly Drawing, pull and push rod, including section through centre
Insert manufacturing drawing
How to hand in your project:
Create pdf files of this document and your drawings. Post these on blackboard.
Remember this is a group project where all group members will be given the same mark. All work,
including drawings and calculations should be different from other groups. Groups submitting very
similar drawings will be reported to the College Unfair Practice process.
EG-165 Design Project 1 – Pull rod and push rod - FEEDBACK
Levels of Achievement
Criteria Novice Competent Proficient Excellent
2 Points 3 Points 4 Points 5 Points
Calculations
Incomplete Significant Errors Minor Errors Accurate
5 Points
2 Points 3 Points 4 Points
Perfectly laid out and
Drawing below Average drawing, Good tidy
dimensioned drawing.
Assembly standard. Doesn't slightly untidy. drawing.
Components perfectly
Drawings fit. Structurally Reasonable design. Competent design
sized. Assembly
Weak. Essential Some omissions of with all features
method and alignment
items missing. detailing. included.
good.
Insert 3 Points 4 Points
2 Points 5 Points
Manufacturing Not possible to Competent with
Below Standard Perfect for manufacture
Drawing manufacture from minor errors
4 Points
2 Points 3 Points 5 Points
Weight Competitive
Above 220g Between 170-220g Lowest Weight Group
below 170g
, Specification Pull Rod Push Rod
Material Choice (Include Aluminium 6082T6 Aluminium 6082T6
specific alloy details)
Material yield stress (MPa) 310 310
Material Young’s Modulus 70 70
(GPa)
Outside Diameter (mm) 12.7 12.7
Inside Diameter (mm) 9.449 9.449
Wall Thickness (mm) 3.251 3.251
Input load (N) 1751.26835 1751.26835
Stress in tension (MPa) 30.9664717
Maximum buckling limit (N) 5201.146
Stress in bolt 2 (MPa) 40.4496 40.4496
Rod end manufacturer and part Aurora AM-M5 rod end Aurora AM-M5 rod end
number (Right Hand thread) bearing bearing
Rod end manufacturer and part Aurora AM-M5 rod end Aurora AM-M5 rod end
number (Left Hand thread) bearing bearing
Weights
Bar/tube (g) 61 61
Two inserts (g) 10 10
Two Rod Ends (g) 131 13
Total weight of 1x pull rod assembly +1x push rod assembly (g) 168
