AFAB 110 FINAL EXAM QUESTIONS WITH CORRECT ANSWERS LATEST UPDATE 2026
The word print can best be used the same as the word _____________ - Answers Drawing
In many cases, the print is also an important part of a _______________ in the industrial setting. -
Answers Contract
The study of print reading is closely related to the study of _____________, the general term for
creating drawings of objects in technical fields. - Answers Drafting
PDF is an electronic file format that allows the user to share a drawing or image without giving them
the actual CAD data file. PDF stands for __________________. - Answers Portable Document Format
A voluntary guideline that establishes the method of representation for prints, as well as other
engineering practices, is a ________________. - Answers Standard
Identify the line below that is fictitious. - Answers Dotted line
Cutting-plane lines are easily identifiable due to the appearance of a(n) ___________ on each end of
the line. - Answers Arrowhead
Identify the line below that is to be drawn thick. - Answers Cutting-plane line
The standardized list of line types, perhaps in the form of a chart, is defined in many references as the
________________. - Answers Alphabet of line
Print reading is the process of analyzing a print to obtain information. This task involves two principal
elements: visualization and _____________. - Answers Interpretation
If a D-size sheet of paper is properly cut, how many A-size sheets should result? - Answers 8
For which of the following is least likely to be found on a basic parts list? - Answers Finish
A block that is important to read in the early stage of examining a print is the ___________ block,
which helps determine if the print being observed is up-to-date. - Answers Revision history
Which of the following is least likely to be found on a basic parts list? - Answers Finish
The word that basically means "cut in half" is _______________. - Answers Bisect
If a hexagon is inscribed within a circle, the diameter of the circle is equivalent to the term
__________. - Answers Across-the-corners
In most CAD systems, the basic geometric forms used to create complex models are referred to as
_______________. - Answers Primitives
As lines are parallel to each other, arcs are ________________ to each other. - Answers Concentric
Which of the following is a way to describe the point of tangency between two circles? - Answers
Found on a line connecting the two center points
Which of the following cannot be defined by the way a plane intersects a cone? - Answers Ogee curve
Which of the following is not an example of a spatial visualization instrument? - Answers Playing 3D
tic-tac-toe
There are three dimension terms common to drafting education. Which of the following is not
correct? - Answers Length
The type of section view wherein the cutting-plane line has bends to accommodate several features
that are not aligned is a(n) ________ section. - Answers Offset
Cylindrical object with an odd number of features, such as pokes or holes on a bolt circle, could better
be described with a(n) ___________ section. - Answers Aligned
The broken-out section requires another type of line from the alphabet of lines to help show where
the removed portion was broken off in a "jagged" sort of way. This is the _____________ line. -
Answers Short break
When a(n) _____________ section is created, it can be overlaid on the view or short break lines can
be used on each side of the view to separate it from the other visible lines. - Answers Revolved
Type of section wherein the section view is probably located out of projection with the other regular
or auxiliary views is a(n) ___________ section. - Answers Removed
There is a conventional practice that allows the drafter to leave a feature unhatched, even though the
cutting-plane line passes through it. Which of the following is not relevant to this conventional
practice? - Answers Hole
If there is a large area that needs to receive section lines, the _________ section allows for the section
lines to only be applied around the perimeter. - Answers Outline
In assembly drawings, there may be some parts that do not receive section lines, but rather the area
cut by the cutting-plane line is filled-in solid. Which of the following is not relevant to this
conventional practice? - Answers Springs
The word print can best be used the same as the word _____________ - Answers Drawing
In many cases, the print is also an important part of a _______________ in the industrial setting. -
Answers Contract
The study of print reading is closely related to the study of _____________, the general term for
creating drawings of objects in technical fields. - Answers Drafting
PDF is an electronic file format that allows the user to share a drawing or image without giving them
the actual CAD data file. PDF stands for __________________. - Answers Portable Document Format
A voluntary guideline that establishes the method of representation for prints, as well as other
engineering practices, is a ________________. - Answers Standard
Identify the line below that is fictitious. - Answers Dotted line
Cutting-plane lines are easily identifiable due to the appearance of a(n) ___________ on each end of
the line. - Answers Arrowhead
Identify the line below that is to be drawn thick. - Answers Cutting-plane line
The standardized list of line types, perhaps in the form of a chart, is defined in many references as the
________________. - Answers Alphabet of line
Print reading is the process of analyzing a print to obtain information. This task involves two principal
elements: visualization and _____________. - Answers Interpretation
If a D-size sheet of paper is properly cut, how many A-size sheets should result? - Answers 8
For which of the following is least likely to be found on a basic parts list? - Answers Finish
A block that is important to read in the early stage of examining a print is the ___________ block,
which helps determine if the print being observed is up-to-date. - Answers Revision history
Which of the following is least likely to be found on a basic parts list? - Answers Finish
The word that basically means "cut in half" is _______________. - Answers Bisect
If a hexagon is inscribed within a circle, the diameter of the circle is equivalent to the term
__________. - Answers Across-the-corners
In most CAD systems, the basic geometric forms used to create complex models are referred to as
_______________. - Answers Primitives
As lines are parallel to each other, arcs are ________________ to each other. - Answers Concentric
Which of the following is a way to describe the point of tangency between two circles? - Answers
Found on a line connecting the two center points
Which of the following cannot be defined by the way a plane intersects a cone? - Answers Ogee curve
Which of the following is not an example of a spatial visualization instrument? - Answers Playing 3D
tic-tac-toe
There are three dimension terms common to drafting education. Which of the following is not
correct? - Answers Length
The type of section view wherein the cutting-plane line has bends to accommodate several features
that are not aligned is a(n) ________ section. - Answers Offset
Cylindrical object with an odd number of features, such as pokes or holes on a bolt circle, could better
be described with a(n) ___________ section. - Answers Aligned
The broken-out section requires another type of line from the alphabet of lines to help show where
the removed portion was broken off in a "jagged" sort of way. This is the _____________ line. -
Answers Short break
When a(n) _____________ section is created, it can be overlaid on the view or short break lines can
be used on each side of the view to separate it from the other visible lines. - Answers Revolved
Type of section wherein the section view is probably located out of projection with the other regular
or auxiliary views is a(n) ___________ section. - Answers Removed
There is a conventional practice that allows the drafter to leave a feature unhatched, even though the
cutting-plane line passes through it. Which of the following is not relevant to this conventional
practice? - Answers Hole
If there is a large area that needs to receive section lines, the _________ section allows for the section
lines to only be applied around the perimeter. - Answers Outline
In assembly drawings, there may be some parts that do not receive section lines, but rather the area
cut by the cutting-plane line is filled-in solid. Which of the following is not relevant to this
conventional practice? - Answers Springs
