Airline interview TECHNICAL QUESTIONS AND CORRECT
ANSWERS WITH RATIONALES AND RATIONALES.
Airline Interview Technical Questions – Questions 1–30
Question 1
What does V1 speed signify during takeoff?
A. Decision speed – the speed by which the takeoff must continue or be aborted
B. Maximum landing speed
C. Rotation speed
D. Stall speed
Correct Answer: A
Rationale:
V1 is the critical decision speed. Below V1, takeoff can be rejected; above V1, takeoff must continue
even if an engine fails.
Question 2
What is V2 speed?
A. Takeoff safety speed – ensures aircraft can climb safely with one engine inoperative
B. Maximum cruise speed
C. Stall speed
D. Rotation speed
Correct Answer: A
Rationale:
V2 provides safe climb performance after engine failure during takeoff.
Question 3
What is VR speed?
A. Rotation speed – speed at which pilot initiates nose lift during takeoff
B. Decision speed
C. Landing speed
D. Stall speed
, Correct Answer: A
Rationale:
VR ensures aircraft lifts off safely without stalling or structural stress.
Question 4
What is the purpose of the APU?
A. Provides electrical power and bleed air on the ground or in emergency
B. Controls flaps
C. Measures airspeed
D. Operates landing gear
Correct Answer: A
Rationale:
APU powers essential systems when engines are off or in certain emergencies.
Question 5
What is MEL?
A. Minimum Equipment List – allows flight with certain inoperative systems
B. Maximum Engine Limit
C. Manual Entry Log
D. Main Electrical Line
Correct Answer: A
Rationale:
MEL ensures regulated safe operation with limited inoperative equipment.
Question 6
What does TCAS RA stand for?
A. Traffic Collision Avoidance System – Resolution Advisory
B. Throttle Control Adjustment
C. Terrain Caution Alert System
D. Cabin pressurization alert
Correct Answer: A
Rationale:
TCAS RAs provide corrective instructions to avoid mid-air collisions.
Question 7
, What is VMC?
A. Minimum control speed for multi-engine aircraft
B. Maximum cruise speed
C. Stall speed
D. Rotation speed
Correct Answer: A
Rationale:
VMC ensures control with one engine inoperative; crucial for multi-engine aircraft performance.
Question 8
What is RVSM?
A. Reduced Vertical Separation Minimum – allows closer safe vertical spacing
B. Runway Visual Safety Measure
C. Reverse Velocity Speed Module
D. Remote Vehicle System Management
Correct Answer: A
Rationale:
RVSM enhances airspace capacity while maintaining safety at high altitudes.
Question 9
What is ETOPS?
A. Extended Twin-engine Operations – planning for long-distance flights with one engine inoperative
B. Engine Thrust Optimization Procedure
C. Emergency Takeoff Planning System
D. Electrical Transmission Operating System
Correct Answer: A
Rationale:
ETOPS ensures safe diversion planning and operational reliability for twin-engine aircraft.
Question 10
What is FMS?
A. Flight Management System – automates navigation, performance, and fuel calculations
B. Flap Management System
C. Fuel Monitoring System
D. Flight Mode Selector
Correct Answer: A
ANSWERS WITH RATIONALES AND RATIONALES.
Airline Interview Technical Questions – Questions 1–30
Question 1
What does V1 speed signify during takeoff?
A. Decision speed – the speed by which the takeoff must continue or be aborted
B. Maximum landing speed
C. Rotation speed
D. Stall speed
Correct Answer: A
Rationale:
V1 is the critical decision speed. Below V1, takeoff can be rejected; above V1, takeoff must continue
even if an engine fails.
Question 2
What is V2 speed?
A. Takeoff safety speed – ensures aircraft can climb safely with one engine inoperative
B. Maximum cruise speed
C. Stall speed
D. Rotation speed
Correct Answer: A
Rationale:
V2 provides safe climb performance after engine failure during takeoff.
Question 3
What is VR speed?
A. Rotation speed – speed at which pilot initiates nose lift during takeoff
B. Decision speed
C. Landing speed
D. Stall speed
, Correct Answer: A
Rationale:
VR ensures aircraft lifts off safely without stalling or structural stress.
Question 4
What is the purpose of the APU?
A. Provides electrical power and bleed air on the ground or in emergency
B. Controls flaps
C. Measures airspeed
D. Operates landing gear
Correct Answer: A
Rationale:
APU powers essential systems when engines are off or in certain emergencies.
Question 5
What is MEL?
A. Minimum Equipment List – allows flight with certain inoperative systems
B. Maximum Engine Limit
C. Manual Entry Log
D. Main Electrical Line
Correct Answer: A
Rationale:
MEL ensures regulated safe operation with limited inoperative equipment.
Question 6
What does TCAS RA stand for?
A. Traffic Collision Avoidance System – Resolution Advisory
B. Throttle Control Adjustment
C. Terrain Caution Alert System
D. Cabin pressurization alert
Correct Answer: A
Rationale:
TCAS RAs provide corrective instructions to avoid mid-air collisions.
Question 7
, What is VMC?
A. Minimum control speed for multi-engine aircraft
B. Maximum cruise speed
C. Stall speed
D. Rotation speed
Correct Answer: A
Rationale:
VMC ensures control with one engine inoperative; crucial for multi-engine aircraft performance.
Question 8
What is RVSM?
A. Reduced Vertical Separation Minimum – allows closer safe vertical spacing
B. Runway Visual Safety Measure
C. Reverse Velocity Speed Module
D. Remote Vehicle System Management
Correct Answer: A
Rationale:
RVSM enhances airspace capacity while maintaining safety at high altitudes.
Question 9
What is ETOPS?
A. Extended Twin-engine Operations – planning for long-distance flights with one engine inoperative
B. Engine Thrust Optimization Procedure
C. Emergency Takeoff Planning System
D. Electrical Transmission Operating System
Correct Answer: A
Rationale:
ETOPS ensures safe diversion planning and operational reliability for twin-engine aircraft.
Question 10
What is FMS?
A. Flight Management System – automates navigation, performance, and fuel calculations
B. Flap Management System
C. Fuel Monitoring System
D. Flight Mode Selector
Correct Answer: A
