NWSA TEST || with Errorless Answers.
American National Standards Institute (ANSI) correct answers Who is the third-party group that
approves and endorses standards?
Standards correct answers What term is used to describe the documents written by members, or
peers, in the industry.
Industry Standards correct answers Company's Health, Safety and Environment policy should be
a combination of Labor Regulations and _________?
Employer correct answers Where OSHA has not promulgated specific standards, who is
responsible for following the act's general duty clause?
The whole crew correct answers On a job site who should be involved in the JHA process?
Scope of Work correct answers What does the term SOW stand for?
Job Hazard Assessment correct answers What does the term SOW stand for?
3 feet correct answers When using an extension ladder, how many feet past the platform must it
extend?
4 feet correct answers If you have a sixteen-foot ladder leaning against a building wall, how
many feet from the wall does the case need to be to provide the correct slope?
Personal Protective Equipment correct answers What do the letters PPE stand for?
-Senses a short circuit.
, -Prevents electrocution.
-Shuts off the flow of electricity correct answers What does a ground fault circuit Interrupter
(GFCI) do?
Employer correct answers Who is responsible for providing the applicable PPE for a work site?
Shoulder level or above correct answers When using a Y-lanyard attached to your back d-ring, at
what height should the connection to your anchorage be place? Extend?
Nine inches correct answers What is the maximum distance between the sternal d-ring and the
fixed safety climb?
Four feet correct answers When calculating a fall distance using a "6 foot" energy absorber, what
is the maximum pull out distance?
Two times the arresting force or 3,000 lbs. correct answers When calculating a fall distance using
a "6 foot" energy absorber, what is the maximum pull out distance?
5,000 lbs correct answers What minimum force must a non-engineered anchor be able to
withstand for fall protection use?
3,600 lbs correct answers What minimum force must an engineered anchor be able to withstand
for fall protection use?
3,600 lbs correct answers On any fall protection component, the latch must be double locking
and be designed to withstand how many pounds of force?
1,000 lbs correct answers When using a Fall Restraint system, what is the minimum anchorage
allowed?
American National Standards Institute (ANSI) correct answers Who is the third-party group that
approves and endorses standards?
Standards correct answers What term is used to describe the documents written by members, or
peers, in the industry.
Industry Standards correct answers Company's Health, Safety and Environment policy should be
a combination of Labor Regulations and _________?
Employer correct answers Where OSHA has not promulgated specific standards, who is
responsible for following the act's general duty clause?
The whole crew correct answers On a job site who should be involved in the JHA process?
Scope of Work correct answers What does the term SOW stand for?
Job Hazard Assessment correct answers What does the term SOW stand for?
3 feet correct answers When using an extension ladder, how many feet past the platform must it
extend?
4 feet correct answers If you have a sixteen-foot ladder leaning against a building wall, how
many feet from the wall does the case need to be to provide the correct slope?
Personal Protective Equipment correct answers What do the letters PPE stand for?
-Senses a short circuit.
, -Prevents electrocution.
-Shuts off the flow of electricity correct answers What does a ground fault circuit Interrupter
(GFCI) do?
Employer correct answers Who is responsible for providing the applicable PPE for a work site?
Shoulder level or above correct answers When using a Y-lanyard attached to your back d-ring, at
what height should the connection to your anchorage be place? Extend?
Nine inches correct answers What is the maximum distance between the sternal d-ring and the
fixed safety climb?
Four feet correct answers When calculating a fall distance using a "6 foot" energy absorber, what
is the maximum pull out distance?
Two times the arresting force or 3,000 lbs. correct answers When calculating a fall distance using
a "6 foot" energy absorber, what is the maximum pull out distance?
5,000 lbs correct answers What minimum force must a non-engineered anchor be able to
withstand for fall protection use?
3,600 lbs correct answers What minimum force must an engineered anchor be able to withstand
for fall protection use?
3,600 lbs correct answers On any fall protection component, the latch must be double locking
and be designed to withstand how many pounds of force?
1,000 lbs correct answers When using a Fall Restraint system, what is the minimum anchorage
allowed?
