BMW Associate level ASE test latest
Version Updated 2024.
a lifting pad must be in place to lift a BMW vehicle, T or F? - ANSWER-True
A technician should consider which of the following questions for a quality control process after
performing service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above - ANSWER-All of the above
According to MSDS warning symbols, the warning symbol with a skull and cross bones shown
represents - ANSWER-Acute toxicity
All BMW special tools are auto ship to the dealer.
True or False? - ANSWER-False
All brand-new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching device. -
ANSWER-Both A and B
All of the following are true concerning the Roundtable, EXCEPT :
There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz - ANSWER-The Roundtable is accessed through AIR.
, Battery voltage is not critical when performing a voltage drop on a circuit.
True or False? - ANSWER-False
BMW recommends replacing tire at least every 6 years
what resource can you use to determine that the above statement is correct? - ANSWER-Owners
Manual
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure - ANSWER-Brake pad thickness and tire thread depth
CPO inspections require a minimum tread depth of 3 mm, as measured from the lowest area in the
tread. T or F? - ANSWER-False (from top of wear indicators)
During a CPO inspection, a front brake pad measurement is taken of 4mm on the left inner pad and
7mm on the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed specifications.
Who is correct? - ANSWER-Neither A or B
During a CPO inspection, all of the following items will need to be addressed before the CPO sale,
EXCEPT:
Mismatched tires
Aftermarket windshield
OEM brake pads with 4mm thickness of material remaining
Wheel with a lateral runout of 1.2mm - ANSWER-Aftermarket windshield
Version Updated 2024.
a lifting pad must be in place to lift a BMW vehicle, T or F? - ANSWER-True
A technician should consider which of the following questions for a quality control process after
performing service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above - ANSWER-All of the above
According to MSDS warning symbols, the warning symbol with a skull and cross bones shown
represents - ANSWER-Acute toxicity
All BMW special tools are auto ship to the dealer.
True or False? - ANSWER-False
All brand-new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching device. -
ANSWER-Both A and B
All of the following are true concerning the Roundtable, EXCEPT :
There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz - ANSWER-The Roundtable is accessed through AIR.
, Battery voltage is not critical when performing a voltage drop on a circuit.
True or False? - ANSWER-False
BMW recommends replacing tire at least every 6 years
what resource can you use to determine that the above statement is correct? - ANSWER-Owners
Manual
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure - ANSWER-Brake pad thickness and tire thread depth
CPO inspections require a minimum tread depth of 3 mm, as measured from the lowest area in the
tread. T or F? - ANSWER-False (from top of wear indicators)
During a CPO inspection, a front brake pad measurement is taken of 4mm on the left inner pad and
7mm on the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed specifications.
Who is correct? - ANSWER-Neither A or B
During a CPO inspection, all of the following items will need to be addressed before the CPO sale,
EXCEPT:
Mismatched tires
Aftermarket windshield
OEM brake pads with 4mm thickness of material remaining
Wheel with a lateral runout of 1.2mm - ANSWER-Aftermarket windshield
