Final Exam Study Guide Lineman School Book/Safety Test 2022

Final Exam Study Guide Lineman School Book/Safety Test 2022 1. Students that climb structures, ladders, or use climbers shall wear a substantial work type shoe or boot with: A. Instep Guards B.A well defined heel C.Soles of synthetic rubber, cork, or cord: B.A well defined heel 2. Which of the following statements regarding hard hats is false? A.The hat shell should occasionally be cleaned with a mild solvent B.The shell and suspension work together to absorb and disperse Shock C.The hat's ability to protect may be adversely affected if it is worn back- wards: A.The hat shell should occasionally be cleaned with a mild solvent 3. Which of the following statements regarding safety glasses is false? A.Scratches on glass lenses affect the lens strength B.Scratches on plastic lenses affect the lens strength C.Scratches on plastic lenses do not affect the lens strength: B.Scratches on plastic lenses affect the lens strength 4. Hand injuries can be prevented by wearing the proper glove of the correct fit. A glove that is too small: A. Leads to unsure handling B. Tends to catch on things C. Promotes hand fatigue: C.Promotes hand fatigue 5. Many pieces of PPE are specialty items; that is, they have a very specific use. Answers to questions regarding the application of a particular piece of PPE can be obtained by contacting: A. The Safety Department or your supervisor B.A Procedures Counselor within the Human Resources Department C.A Workstation Expert within the Information Technologies Dept.: A.The Safety Department or your supervisor 6. During the first six months in this classification, the students demonstrate the ability to operate company equipment, climb poles and structures, and work on de-energized conductors and equipment. Also, A. Under direct supervision of a higher classification, may work secondary voltage up to 260 volts B. Under general supervision of a higher classification, may work secondary voltage up to 260 volts C. Under immediate supervision of a higher classification, may work sec- ondary voltage up to 260 volts: C.Under immediate supervision of a higher classification, may work secondary voltage up to 260 volts 7. Which of the following is not a routine duty of "D" mechanics? A. Assemble, install, maintain, remove and inspect conductors, fixtures and other associated equipment on energized overhead and underground facili- ties over 260 volts B. Climb poles and structures and work from bucket trucks or on ladders and demonstrate evidence of being at ease above the ground in performance of work C. Operate mechanized equipment required to install, remove or maintain overhead and underground transmission and distribution facilities: A. As- semble, install, maintain, remove and inspect conductors, fixtures and other as- sociated equipment on energized overhead and underground facilities over 260 volts 8. After six months in this classification, under general supervision, a "D" mechanic may work on conductors and equipment energized at voltages up to: A.160 B.260 C.360: B.260 9. Which of the following is not a routine duty of "D" mechanics? A.Perform similar or higher skilled work B.Assist employees of equal or higher classification C.Attend or participate in training as assigned and assist in the training of other students: A.Perform similar or higher skilled work 10. A "qualified person" is defined as one who is: A.Knowledgeable of the task at hand and not necessarily at the job site B.In constant visual and/or verbal contact with the person performing the designated task C.Knowledgeable of the task at hand is capable of performing the appro- priate emergency rescue: C.Knowledgeable of the task at hand is capable of performing the appropriate emergency rescue 11. The minimum listing of rules and regulations by which work is to be planned and carried out safely is the: A.Safety Manual B.Distribution Standards C.Lineman's and Cableman's Handbook: A.Safety Manual 12. A simplified drawing of distribution circuitry showing conductor sizes, system protection devices, switching points, etc. is known as a: A.Distribution standard B.Distribution one-line diagram C.Hazard Communication: B.Distribution one-line diagram 13. A general resource for workers of the line industry is a work known as: A.The Lineman's and Cableman's Handbook B.OSHA Regulation