NIMS MMS COMPREHENSIVE EXAM 2026 QUESTIONS AND
ANSWERS GRADED A+
✔✔Inspection plans are needed to: - ✔✔Coordinate inspection procedures, identifying
measuring tools, check dimensions in a repeatable and reliable way
✔✔The first thing to do when constructing an inspection plan is to: - ✔✔select the
critical and important dimensions to inspect
✔✔The most important factor in selecting measuring tools for inspection is -
✔✔tolerancing of dimensions to inspect
✔✔Sampling plans contribute to a quality control process by: - ✔✔providing an
acceptable representation of all parts produced
✔✔What feature of a thread is checked with a thread micrometer? - ✔✔pitch diameter
✔✔Dial bore gages are used to measure: - ✔✔holes
✔✔To indicate an angled surface & make that surface parallel to a surface plate, a
machinist uses: - ✔✔sine plate
✔✔What sizes of gage pins are needed for a dimension o 9/32 + or - 1/64 inches -
✔✔.297/.266
✔✔A measure of dispersion that uses the largest and smallest measurements of a
sampling is the: - ✔✔Range
✔✔What is the range of the following sampling: ( 0.345, 0.382, 0.353, 0.380, 0.377)? -
✔✔0.037
✔✔Which of the following is not found on an X-bar and R control chart? - ✔✔Capability
ratio
✔✔The acronym MSDS means: - ✔✔Material Safety Data Sheet
✔✔Which of the following colors is not found on an HMIS label? - ✔✔Green
✔✔The threshold limit value ( TLV) is defined as - ✔✔the safe limit of unprotected
exposure to a material
✔✔MSDS information on new chemicals and materials found in the workplace can be
reviewed at - ✔✔Right to Know seminars and classes Safety seminars
ANSWERS GRADED A+
✔✔Inspection plans are needed to: - ✔✔Coordinate inspection procedures, identifying
measuring tools, check dimensions in a repeatable and reliable way
✔✔The first thing to do when constructing an inspection plan is to: - ✔✔select the
critical and important dimensions to inspect
✔✔The most important factor in selecting measuring tools for inspection is -
✔✔tolerancing of dimensions to inspect
✔✔Sampling plans contribute to a quality control process by: - ✔✔providing an
acceptable representation of all parts produced
✔✔What feature of a thread is checked with a thread micrometer? - ✔✔pitch diameter
✔✔Dial bore gages are used to measure: - ✔✔holes
✔✔To indicate an angled surface & make that surface parallel to a surface plate, a
machinist uses: - ✔✔sine plate
✔✔What sizes of gage pins are needed for a dimension o 9/32 + or - 1/64 inches -
✔✔.297/.266
✔✔A measure of dispersion that uses the largest and smallest measurements of a
sampling is the: - ✔✔Range
✔✔What is the range of the following sampling: ( 0.345, 0.382, 0.353, 0.380, 0.377)? -
✔✔0.037
✔✔Which of the following is not found on an X-bar and R control chart? - ✔✔Capability
ratio
✔✔The acronym MSDS means: - ✔✔Material Safety Data Sheet
✔✔Which of the following colors is not found on an HMIS label? - ✔✔Green
✔✔The threshold limit value ( TLV) is defined as - ✔✔the safe limit of unprotected
exposure to a material
✔✔MSDS information on new chemicals and materials found in the workplace can be
reviewed at - ✔✔Right to Know seminars and classes Safety seminars
