NCCER

Blue Prints An exact copy of reproduction of an original drawing Floor plan As viewed from above Site plan Location of building on the property Surveys show All property lines, existing public utilities and their location on or near the property Elevation drawings show The exterior face of the building Floor plans are in 2 dimension, length and width Topographic survey shows Property lines, contour lines, notes and symbols

What are the two most common hammers? Claw hammer Ball-peen Hammer Which hammer is also called the engineer's hammer or machinist's hammer? Ball-peen hammer What heavy-duty tool is used to drive posts and other large stakes? sledgehammer What are the three main types of nail-pulling tools? Cat's Paw (Nail claws) Chisel bar Wrecking bar (ripping bar, wonder bar) What is the name of a metal tool with a sharpened, beveled edge? Chisel What is the degree for the angle of the edge of a co...

A cutaway view of a building or object is known as a(n)______. Sectional drawing What is the total connected load of Circuit A-1 if each of the Type C lighting fixtures in the figure above has a total lamp and ballast load of 150VA? 1,200VA In which division of the MasterFormat is electronic safety covered? Division 28 A section line on a drawing shows The location of the section on the plan On electrical drawings, a solid line with a solid circle at the end indicates wiring______. Turn do...

What are benefits of safety Lower accident rates less turnover Arc welding safety Gas welding and burning requires the use of a filter lens of not less than No. 4 shade Safety A learned behavior and attitude Safety culture A safety culture is created when the whole company sees the value of a safe work environment Strong safety culture Effective communication and commonly and understood and agreed upon goals Accidents An unplanned event that may our may not result in personal injury or ...

companies with strong safety cultures usually have lower? incident and accident rates what is a statement regarding safety? it's a learned behavior and attitude poor lighting, excessive noise, and inadequate guards for moving parts are examples of? unsafe conditions the activity that consists of breaking a job into its component tasks and then analyzing each step for potential hazards is called a? job safety analysis JSA a measure of the probability, consequences, and exposure related to ...

1. The number matching the words "two thousand, six hundred eighty-nine" is a. 2,286 b. 2,689 c. 6,289 d. 20,689 b. 2,689 2. A bricklayer lays 649 bricks the first day, 632 the second day, and 478 the third day. During the three-day period, the bricklayer laid a total of a. 1,759 b. 1,760 c. 1,769 d. 1,770 a. 1,759 3. A total of 1,478 feet of cable was supplied for a job. Only 489 feet were installed. How many feet of cable remain?

what is another name for a machinist hammer? Ball-peen hammer a heavy duty tool used to drive posts or other large stakes is called a? Sledgehammer what is the proper angle for the edge of a cold chisel? 60- degrees what types of screw comes to a relative sharp point at the base of its drive socket? Reed and Prince how many sides does a Hexagonal shape have? six sides in what way is a Spud wrench different from a Pipe wrench? the jaws are smooth to quickly run a nut onto a bolt that resis...

A saw that has a thin one-piece blade that runs around guides, that runs around either end of the saw is a Band saw A power miter saw combines a miter box with a Circular saw An angle grinder is used to grind Hard heavy materials The adjustable tool rest on a bench grinder should be positioned One eighth of an inch from the grinding tool A good way to check the condition of the grinding wheel on a bench grinder is to Perform a ring test A grinder can catch on rough material edges and shi...

1. Pneumatic tools get their power from a. air pressure b. fluid pressure c. hand pumps d. AC power sources a. air pressure 2. The most common use of the power drill is to a. cut wood, metal, and plastic b. drive nails into wood, metal, and plastic c. make holes in wood, metal, and plastic d. carve letters in wood, metal, and plastic c. make holes in wood, metal, and plastic 3. A masonry bit is able to drill into concrete and similar material because it has a a. countersink shank b. cerami...

when using power tools, never engage the? trigger lock. before replacing parts such as bits, blades or disks on any tool, you must? make sure it is disconnected from its source or energy most hammer drills will not hammer until pressure is? applied to the drill bit against a surface a pneumatic drill is commonly used? when there is no source of electricity never use a circular saw that does not have an upper blade guard because? it protects workers from flying debris and from touching the...

Plans used for work that has to do with construction in or on the earth are called Civil Plans The material used for the walls would be found in the? Structural Plans Information in a drawings title block identifies the project on the Sheet Title Information needed to identify lines in the symbols in a construction file can be found in the Legend Brake lines are used to show that Only part of an object is represented to save space In the alphabet lines an area not included in the cutting l...

the max load weight that a sling is designed to carry is the? rated capacity most alloy steel chain slings can be used in Temps up to? 500°F (260°c) when a tattle tail has been pulled into the jacket of a synthetic sling, the sling most likely has been? overloaded if a wire rope sling appears to be damaged the decision to keep it in service must be made by a? competent person because of the need for increased toughness, shackles for most overhead lifting are made from? forged steel wit...

in the study of communication, noise is best described as? anything that interferes with a message being heard or understood folding your arms in front of you makes it seem as if you are? distant/unwilling to talk if someone does not understand what a speaker is saying, he or she should? ask questions when listening to instructions, the best way for listeners to make sure they get all the information is to? paraphrase an important attribute of an effective speaker is the ability to? make s...

If you see a potential source of delay on a project, notify your __________immediately. supervisor The way you speak, act, and interact is called self-___________. presentation Being _____________ means showing up for work on time, every day. dependable Discrimination towards an individual based on race, sex, religion, cultural issues, or language barriers is known as? harassment Computer systems consist of what three things? hardware, software, and operating systems Machine tools that ar...

a companies documented philosophy is called its? mission statement the time to learn about a potential employer is? before an application is ever submitted when preparing a resume, you should? format your resume chronologically during a job search, it is good practice to? look for a job that will match your skill level before employment begins, candidates for construction jobs most often? have a drug test submitted how do most employers advertise job openings? on the internet and require o...

The way a person dresses, speaks, acts, and interacts with others Self-presentation A company's documented philosophy is called its: Mission statement. The time to learn about a potential employer is: Before the application is submitted. When preparing a resume, you should: Format the information chronologically. During a job search, it is a good practice to: Look for jobs that match your skills and experience. Before employment begins, candidates for construction jobs must often: Take an...

A tool feature added for convenience that turned out to be very unsafe and should never be used is the... Trigger Lock. Before changing the blade or bit or doing any kind of repair... Unplug the Tool! Before plugging in tools with on/off switches... Turn it off! Most commonly used to make holes but with the right bit can be used as a sander, polisher, screwdriver, grinder, or countersink tool. Power Drill If you can't loosen the drill chuck by hand to remove the drill bit then you probabl...

Companies with strong safety cultures usually have lower _ . turnover Safety is a learned behavior and attitude. T/F TRUE Poor lighting, excessive noise, inadequate guards for moving parts are examples of _ _. unsafe conditions The activity that consists of breaking a job into its component task and then analyzing each step for potential hazards is called _ _ _ . job safety analysis The measure of probability, consequences, and exposure related to an event is referred to as _ . Risk If t...

A UL listed rod type ground electrode must have minimum length of 8'' in a circuit of pure capacitance, the current leads the voltage by 90 degrees The standard unit for measuring the cross sectional area of wire is the circular mil the drawing scale is most likely to be found in the drawing title block what is the minimum number of overload sensing units required for all three phase motors 3 what is the resultant distance between center bends for a 10-inch offset at 15 degrees 38.7 inch...

the max load weight that a sling is designed to carry is the? rated capacity most alloy steel chain slings can be used in Temps up to? 500°F (260°c) when a tattle tail has been pulled into the jacket of a synthetic sling, the sling most likely has been? overloaded if a wire rope sling appears to be damaged the decision to keep it in service must be made by a? competent person because of the need for increased toughness, shackles for most overhead lifting are made from? forged steel wit...