PIPE FITTER TEST LATEST
The 3 MAJOR trig functions are..
Tangent, Cosine, and Stine
The working load limit of hoisting equipment is based on a straight,
vertical hoist line and..
The load being freely suspended
Which drawing gives enough information to be able to fabricate a
pipe run?
Isometric
Which of the following tools should be used to install a 2" threaded
chrome plated pipe in a fitting?
Strap wrench
The rigger MUST carefully inspect the chain hoist.. WHEN?
before each use
Information referring to design requirements and materials for
pipe, flanes, valves, and related iteams to be used is found in...
isometric drawings
All piping and piping components are identified by what
international identification system?
ASTM
What is the highest safe standing step or level from the top of a step
ladder (A-Frame)
END OF
PAGE
1
, PIPE FITTER TEST LATEST
2nd
A plug valve is used to ...
Start and Stop Flow
Ladders should be inspected ...WHEN?
before each use
What does WPS stand for?
Welding Procedure Specification
What does this symbol refer to?
Eccentric reducer
the illustrated piece of equipment is a..
compressor
The illustrated piece of equipment is a..
Centrifugal pump
The illustrated piece of equipment is a..
Compact trencher
What is the piece of equipment shown in the provided figure
Horizontal Drill
The tool shown in the provided figure is used to
Flare Tubing
END OF
PAGE
2
, PIPE FITTER TEST LATEST
What is the attachment shown in the provided figure
Weldless Eye
The flange depicted by the following figure is a..
Lap Joint
What pipe hanger is shown in the following figure
Adjustable Clevis
The hanger shown in the following figure is a(n)
Double Bolt
What type of Spring can Support is shown in the following figure
Constant
What is the tool shown in the provided figure
Nipple Chuck
Convert 1/4 into a decimal
.25
Piping that is field-routed to a pump must be supported..
Independently
what is used when lighting a cutting torch?
END OF
PAGE
3
The 3 MAJOR trig functions are..
Tangent, Cosine, and Stine
The working load limit of hoisting equipment is based on a straight,
vertical hoist line and..
The load being freely suspended
Which drawing gives enough information to be able to fabricate a
pipe run?
Isometric
Which of the following tools should be used to install a 2" threaded
chrome plated pipe in a fitting?
Strap wrench
The rigger MUST carefully inspect the chain hoist.. WHEN?
before each use
Information referring to design requirements and materials for
pipe, flanes, valves, and related iteams to be used is found in...
isometric drawings
All piping and piping components are identified by what
international identification system?
ASTM
What is the highest safe standing step or level from the top of a step
ladder (A-Frame)
END OF
PAGE
1
, PIPE FITTER TEST LATEST
2nd
A plug valve is used to ...
Start and Stop Flow
Ladders should be inspected ...WHEN?
before each use
What does WPS stand for?
Welding Procedure Specification
What does this symbol refer to?
Eccentric reducer
the illustrated piece of equipment is a..
compressor
The illustrated piece of equipment is a..
Centrifugal pump
The illustrated piece of equipment is a..
Compact trencher
What is the piece of equipment shown in the provided figure
Horizontal Drill
The tool shown in the provided figure is used to
Flare Tubing
END OF
PAGE
2
, PIPE FITTER TEST LATEST
What is the attachment shown in the provided figure
Weldless Eye
The flange depicted by the following figure is a..
Lap Joint
What pipe hanger is shown in the following figure
Adjustable Clevis
The hanger shown in the following figure is a(n)
Double Bolt
What type of Spring can Support is shown in the following figure
Constant
What is the tool shown in the provided figure
Nipple Chuck
Convert 1/4 into a decimal
.25
Piping that is field-routed to a pump must be supported..
Independently
what is used when lighting a cutting torch?
END OF
PAGE
3
