Kentucky UST Certification Test Prep EXAM
(updated 2025) Questions & Answers | Latest
Already Graded A+ UPDATE 2025|2026
Save
Students also studied
MN Boiler License Questions WRT Exam CODEWEST API_CB510_exam1.pdf ICC AS
Teacher 157 terms 140 terms Teacher 125 terms Teacher
Rony_Wuodi Preview lamyademmons14 Preview Anna_Mwihaki3 Preview Feli
1. when tanks arrive at the job site, how lifted off with a cable attached to the tank lifting lugs
should they be unloaded?
As an alternative lifting method, should a No, Never!
cable or chain be wrapped around the
tank?
When you are lifting a tank, using the lifting attach a triangle cable through the lugs with no more than a 30 degree angle from
lugs, which of these procedures should be the center line.
followed?
After you unload a new tank on a clean Chock the tank to prevent it from Rolling
level surface at the job site what else
should you do prior to inspection and pre-
testing?
Piping (steel and fiberglass)
which of the following items should be
Fittings, Vents, Fillboxes, anodes, ECT..
physically checked for damage or
The tanks themselves
imperfections at the job site?
(ALL OF THE ABOVE)!
STI-P3 tanks are delivered with shipping remove the plugs and replace them with a standard threaded plug that is properly
plugs in tank openings. What should be doped
done to these plugs prior to testing?
should dielectric bushings be installed in all yes on all openings
openings of an STI-P3 tank?
what is the maximum air pressure to which 5 pounds
a steel tank should be subjected in a pre-
installation test?
for fiberglass reinforced plastic (FRP) tanks 3 pounds
up to 12 feet in diameter what is an
acceptable air pressure to which the tanks
may be subjected in a pre-installation test?
, for FRP tanks over 12 feet in diameter what 3 pounds
is the maximum air pressure to which the
tanks should be subjected in a pre-
installation test?
when you are conducting an air test on a a pressure gauge with a maximum limit of 10 to 15 PSIG
tank the type of gauge that should be used
is?
the proper procedure for conducting a apply 3 to 5 pounds of pressure and soap all surfaces and weld seams visible
pre-installation air test of a steel tank is to? through the coating while inspecting for bubbles.
what is the proper procedure for apply 3 pounds of air pressure and soap all surfaces while inspecting for any sign of
conducting a pre-installation air test of an a leak either audible or visible in the form of bubbles on the surface
FRP tank Under 12 feet in diameter is to....
a double-walled steel tank build in requires air testing of the interstitial space prior to installation
accordance with UL standard 58 is?
the proper procedure for conducting a pressurize the inner tank monitor the pressure for one hour and then pressurize the
pre-installation air test of a double-walled space between the inner and outer tanks with the air from the inner tank
tank is to?
when shipped a steel tank is covered with a should be touched up with a compatible coating after proper surface preparation
coating that is an important part of the
tanks Corrosion Prevention system.
"holidays" which show up in the coating at
the installation site should?
touch up of holidays in a steel tank according to the manufacturer's instructions
coatings at the installation site should be
done.......
dielectric bushings are usually made of non-metallic material
what?
*the tank manufacturers recommendations
factors to consider in determining the size *the requirements for compacting bedding and backfill as well as stability of the soil
shape and depth of a tank excavation *the depth of cover
include what?
AKA all of the above
in the absence of local requirements the 5 feet
recommended minimum distance between
a tank excavation and adjacent structures
or property lines is how many feet?
reinforcement of a steel underground tank the burial depth is greater than the tank diameter
may be required by the tank manufacturer
if
according to FRP tank manufacturers 7 feet
specifications the burial depth for an FRP
tank should not exceed how many feet?
when installing a cathodically protected make sure the excavation is free from material that could cause damage to the
steel tank you should coating
when installing dielectric bushings in a make sure that no electric current can pass through the dielectric flanges or
cathodically protected steel tank prior to bushings
placing the tank in the excavation you
should
(updated 2025) Questions & Answers | Latest
Already Graded A+ UPDATE 2025|2026
Save
Students also studied
MN Boiler License Questions WRT Exam CODEWEST API_CB510_exam1.pdf ICC AS
Teacher 157 terms 140 terms Teacher 125 terms Teacher
Rony_Wuodi Preview lamyademmons14 Preview Anna_Mwihaki3 Preview Feli
1. when tanks arrive at the job site, how lifted off with a cable attached to the tank lifting lugs
should they be unloaded?
As an alternative lifting method, should a No, Never!
cable or chain be wrapped around the
tank?
When you are lifting a tank, using the lifting attach a triangle cable through the lugs with no more than a 30 degree angle from
lugs, which of these procedures should be the center line.
followed?
After you unload a new tank on a clean Chock the tank to prevent it from Rolling
level surface at the job site what else
should you do prior to inspection and pre-
testing?
Piping (steel and fiberglass)
which of the following items should be
Fittings, Vents, Fillboxes, anodes, ECT..
physically checked for damage or
The tanks themselves
imperfections at the job site?
(ALL OF THE ABOVE)!
STI-P3 tanks are delivered with shipping remove the plugs and replace them with a standard threaded plug that is properly
plugs in tank openings. What should be doped
done to these plugs prior to testing?
should dielectric bushings be installed in all yes on all openings
openings of an STI-P3 tank?
what is the maximum air pressure to which 5 pounds
a steel tank should be subjected in a pre-
installation test?
for fiberglass reinforced plastic (FRP) tanks 3 pounds
up to 12 feet in diameter what is an
acceptable air pressure to which the tanks
may be subjected in a pre-installation test?
, for FRP tanks over 12 feet in diameter what 3 pounds
is the maximum air pressure to which the
tanks should be subjected in a pre-
installation test?
when you are conducting an air test on a a pressure gauge with a maximum limit of 10 to 15 PSIG
tank the type of gauge that should be used
is?
the proper procedure for conducting a apply 3 to 5 pounds of pressure and soap all surfaces and weld seams visible
pre-installation air test of a steel tank is to? through the coating while inspecting for bubbles.
what is the proper procedure for apply 3 pounds of air pressure and soap all surfaces while inspecting for any sign of
conducting a pre-installation air test of an a leak either audible or visible in the form of bubbles on the surface
FRP tank Under 12 feet in diameter is to....
a double-walled steel tank build in requires air testing of the interstitial space prior to installation
accordance with UL standard 58 is?
the proper procedure for conducting a pressurize the inner tank monitor the pressure for one hour and then pressurize the
pre-installation air test of a double-walled space between the inner and outer tanks with the air from the inner tank
tank is to?
when shipped a steel tank is covered with a should be touched up with a compatible coating after proper surface preparation
coating that is an important part of the
tanks Corrosion Prevention system.
"holidays" which show up in the coating at
the installation site should?
touch up of holidays in a steel tank according to the manufacturer's instructions
coatings at the installation site should be
done.......
dielectric bushings are usually made of non-metallic material
what?
*the tank manufacturers recommendations
factors to consider in determining the size *the requirements for compacting bedding and backfill as well as stability of the soil
shape and depth of a tank excavation *the depth of cover
include what?
AKA all of the above
in the absence of local requirements the 5 feet
recommended minimum distance between
a tank excavation and adjacent structures
or property lines is how many feet?
reinforcement of a steel underground tank the burial depth is greater than the tank diameter
may be required by the tank manufacturer
if
according to FRP tank manufacturers 7 feet
specifications the burial depth for an FRP
tank should not exceed how many feet?
when installing a cathodically protected make sure the excavation is free from material that could cause damage to the
steel tank you should coating
when installing dielectric bushings in a make sure that no electric current can pass through the dielectric flanges or
cathodically protected steel tank prior to bushings
placing the tank in the excavation you
should
