SOS brake & braking system EXAM Questions &
Answers | 100% Verified solutions |Questions with
Correct Answers 2025 latest update!!
Save
Practice questions for this set
Learn 1 /7 Study with Learn
A brake pedal pulsation during braking.
Choose an answer
A rattle is a single piston disc brake
In a single anchor bendix drum type assembly which goes away when the
1 2
rear brake brakes are applied is most likely a
result of:
Which of the following describes the
Which of the following could be a proper sequence to bleed brake
3 4
symptom of over-torqued lug nuts? lines on most rear wheel drive
vehicles:
, Don't know?
Terms in this set (84)
In a single anchor bendix the secondary lining is longer than the primary
drum type rear brake
Compared to the smaller and goes toward the front of the car
secondary shoe lining
areas of drum brakes, the
primary shoe lining area is:
During a brake overhaul, flush the system before the new parts are installed
you notice that the brake
fluid seems to be very
dirty and dark in color.
What should you do?
In order to bleed the None of the above
system on a vehicle
equipped with power
brakes:
Which of the following A brake pedal pulsation during braking.
could be a symptom of
over-torqued lug nuts?
Which of the following RR, LR, RF, LF
describes the proper
sequence to bleed brake
lines on most rear wheel
drive vehicles:
In disc brake caliper In the caliper piston bore
assemblies, the "square
cut seal" is usually located:
, When performing a Compressed air
caliper overhaul, what
would you use to remove
the pistons from the
calipers?
Sliding caliper disc brake Square cut piston seal
pads are kept in
adjustment by the
A cracked or torn vacuum Hard pedal with very high effort required
diaphragm in a power
booster would likely
cause:
When the brakes are A rotor thickness variation
applied on a car with disc-
drum brakes, a vibration or
pulsating movement is felt.
What can cause this
problem?
While test driving a car, Brake fluid or grease on the brake linings.
the mechanic finds that
the right front brake
"grabs". The most likely
cause of this problem is:
During a road test, you A leaking master cylinder primary piston seal.
find that when normal
breaking pressure is
applied the pedal slowly
goes to the floor. What is
the likely cause of this
problem?
Answers | 100% Verified solutions |Questions with
Correct Answers 2025 latest update!!
Save
Practice questions for this set
Learn 1 /7 Study with Learn
A brake pedal pulsation during braking.
Choose an answer
A rattle is a single piston disc brake
In a single anchor bendix drum type assembly which goes away when the
1 2
rear brake brakes are applied is most likely a
result of:
Which of the following describes the
Which of the following could be a proper sequence to bleed brake
3 4
symptom of over-torqued lug nuts? lines on most rear wheel drive
vehicles:
, Don't know?
Terms in this set (84)
In a single anchor bendix the secondary lining is longer than the primary
drum type rear brake
Compared to the smaller and goes toward the front of the car
secondary shoe lining
areas of drum brakes, the
primary shoe lining area is:
During a brake overhaul, flush the system before the new parts are installed
you notice that the brake
fluid seems to be very
dirty and dark in color.
What should you do?
In order to bleed the None of the above
system on a vehicle
equipped with power
brakes:
Which of the following A brake pedal pulsation during braking.
could be a symptom of
over-torqued lug nuts?
Which of the following RR, LR, RF, LF
describes the proper
sequence to bleed brake
lines on most rear wheel
drive vehicles:
In disc brake caliper In the caliper piston bore
assemblies, the "square
cut seal" is usually located:
, When performing a Compressed air
caliper overhaul, what
would you use to remove
the pistons from the
calipers?
Sliding caliper disc brake Square cut piston seal
pads are kept in
adjustment by the
A cracked or torn vacuum Hard pedal with very high effort required
diaphragm in a power
booster would likely
cause:
When the brakes are A rotor thickness variation
applied on a car with disc-
drum brakes, a vibration or
pulsating movement is felt.
What can cause this
problem?
While test driving a car, Brake fluid or grease on the brake linings.
the mechanic finds that
the right front brake
"grabs". The most likely
cause of this problem is:
During a road test, you A leaking master cylinder primary piston seal.
find that when normal
breaking pressure is
applied the pedal slowly
goes to the floor. What is
the likely cause of this
problem?
