Chapter 7 Solidworks Exam questions
with verified answers
The slope of the Stress-Strain curve in its linear section - correct answer ✔✔What is the
modulus of elasticity?
A measure of the average amount of force exerted per unit area - correct answer ✔✔What is
stress?
-Inertia effects are negligible and loads are applied slowly. -Results are proportional -All
displacements are small relative to the model geometry - correct answer ✔✔Which of the
following assumptions are true for a static analysis in SOLIDWORKS Simulation with small
displacements?
The stress level beyond which material becomes plastic - correct answer ✔✔What is yield
stress?
6 - correct answer ✔✔A high quality Shell element has _____ nodes.
Strain - correct answer ✔✔Stress σ is proportional to ____________ in a Linear Elastic Material.
Stress, Strain - correct answer ✔✔The Elastic Modulus (Young's Modulus) is the slope defined
as _______ divided by __________.
Linear - correct answer ✔✔Linear static analysis assumes that the relationship between loads
and the induced response is ________.
, - correct answer ✔✔In SOLIDWORKS Simulation, the Factor of Safety (FOS) calculations are
based on one of the following failure criterion.
- correct answer ✔✔The Yield point is the point where the material begins to deform at a faster
rate than at the elastic limit. The material behaves ____________ in the Plastic Range.
- correct answer ✔✔What are the Degrees of Freedom (DOFs) restrained for a Solid?
- correct answer ✔✔What are the Degrees of Freedom (DOFs) restrained for Truss joints?
- correct answer ✔✔What are the Degrees of Freedom (DOFs) restrained for Shells and Beams?
- correct answer ✔✔Which statements are true for Material Properties using SOLIDWORKS
Simulation?
- correct answer ✔✔A Beam element has ______ nodes (one at each end) with _______
degrees of freedom per node plus ______ node to define the orientation of the beam cross
section.
- correct answer ✔✔A Truss element has _________ nodes with __________ translational
degrees of freedom per node.
- correct answer ✔✔In general, the finer the mesh the better the accuracy of the results.
- correct answer ✔✔How does SOLIDWORKS Simulation automatically treat a Sheet metal part
with uniform thickness?
- correct answer ✔✔Use the mesh and displacement plots to calculate the distance between
two ________ using SOLIDWORKS Simulation.
with verified answers
The slope of the Stress-Strain curve in its linear section - correct answer ✔✔What is the
modulus of elasticity?
A measure of the average amount of force exerted per unit area - correct answer ✔✔What is
stress?
-Inertia effects are negligible and loads are applied slowly. -Results are proportional -All
displacements are small relative to the model geometry - correct answer ✔✔Which of the
following assumptions are true for a static analysis in SOLIDWORKS Simulation with small
displacements?
The stress level beyond which material becomes plastic - correct answer ✔✔What is yield
stress?
6 - correct answer ✔✔A high quality Shell element has _____ nodes.
Strain - correct answer ✔✔Stress σ is proportional to ____________ in a Linear Elastic Material.
Stress, Strain - correct answer ✔✔The Elastic Modulus (Young's Modulus) is the slope defined
as _______ divided by __________.
Linear - correct answer ✔✔Linear static analysis assumes that the relationship between loads
and the induced response is ________.
, - correct answer ✔✔In SOLIDWORKS Simulation, the Factor of Safety (FOS) calculations are
based on one of the following failure criterion.
- correct answer ✔✔The Yield point is the point where the material begins to deform at a faster
rate than at the elastic limit. The material behaves ____________ in the Plastic Range.
- correct answer ✔✔What are the Degrees of Freedom (DOFs) restrained for a Solid?
- correct answer ✔✔What are the Degrees of Freedom (DOFs) restrained for Truss joints?
- correct answer ✔✔What are the Degrees of Freedom (DOFs) restrained for Shells and Beams?
- correct answer ✔✔Which statements are true for Material Properties using SOLIDWORKS
Simulation?
- correct answer ✔✔A Beam element has ______ nodes (one at each end) with _______
degrees of freedom per node plus ______ node to define the orientation of the beam cross
section.
- correct answer ✔✔A Truss element has _________ nodes with __________ translational
degrees of freedom per node.
- correct answer ✔✔In general, the finer the mesh the better the accuracy of the results.
- correct answer ✔✔How does SOLIDWORKS Simulation automatically treat a Sheet metal part
with uniform thickness?
- correct answer ✔✔Use the mesh and displacement plots to calculate the distance between
two ________ using SOLIDWORKS Simulation.
