MP100 CYCLE 3 FINAL EXAM
How many Aux masters are available on the Neotek Elite? -
ANSWERS-6
When using dynamic processors, should you generally use the insert
or an aux send? - ANSWERS-Insert
When using time-based processors, should you generally use the
insert or an aux send? - ANSWERS-Aux Send (Maintain Wet/Dry
ratio)
Which fader or path should you take your split from for headphone
mixes? Should that split be pre-fader or post-fader and why? -
ANSWERS-Pre Fader, so the return fader level is independent of the
artists level in the headphones
Which fader or path should you take your split from for TBPs?
Should that split be pre-fader or post-fader and why? - ANSWERS-
Post fader, to maintain wet/dry ratio
On the Neotek Elite, can Aux 1 be PRE while Aux 2 on the same I/O
is POST? - ANSWERS-NO
, On the Neotek, can you flip the polarity on the FADER path only, the
MONITOR path only, or both? - ANSWERS-Both because each path
has its own polarity button
On the Neotek, how can you insert the EQ in the FADER path or the
MONITOR path? - ANSWERS-Press either the EQ In Fader or
Monitor Button
On the Neotek Elite, which Aux sends have a PAN control? -
ANSWERS-A and B
What are the four steps to a great headphone mix? - ANSWERS-1.
Make sure you are listening to the same mix as the artist
2. Make sure you are always wearing the headphones when building
or adjusting levels
3. Review the aux method questions and make sure:
-you are splitting off the return
-Splitting pre the return fader
4. Always communicate with the artist
On the Neotek, where is the Mix Mute located? Where is Track Mute
located? - ANSWERS-Mix Mute: BOTTOM of board near solo
button
Track Mute: TOP of board near Multi Track Bus
How many Aux masters are available on the Neotek Elite? -
ANSWERS-6
When using dynamic processors, should you generally use the insert
or an aux send? - ANSWERS-Insert
When using time-based processors, should you generally use the
insert or an aux send? - ANSWERS-Aux Send (Maintain Wet/Dry
ratio)
Which fader or path should you take your split from for headphone
mixes? Should that split be pre-fader or post-fader and why? -
ANSWERS-Pre Fader, so the return fader level is independent of the
artists level in the headphones
Which fader or path should you take your split from for TBPs?
Should that split be pre-fader or post-fader and why? - ANSWERS-
Post fader, to maintain wet/dry ratio
On the Neotek Elite, can Aux 1 be PRE while Aux 2 on the same I/O
is POST? - ANSWERS-NO
, On the Neotek, can you flip the polarity on the FADER path only, the
MONITOR path only, or both? - ANSWERS-Both because each path
has its own polarity button
On the Neotek, how can you insert the EQ in the FADER path or the
MONITOR path? - ANSWERS-Press either the EQ In Fader or
Monitor Button
On the Neotek Elite, which Aux sends have a PAN control? -
ANSWERS-A and B
What are the four steps to a great headphone mix? - ANSWERS-1.
Make sure you are listening to the same mix as the artist
2. Make sure you are always wearing the headphones when building
or adjusting levels
3. Review the aux method questions and make sure:
-you are splitting off the return
-Splitting pre the return fader
4. Always communicate with the artist
On the Neotek, where is the Mix Mute located? Where is Track Mute
located? - ANSWERS-Mix Mute: BOTTOM of board near solo
button
Track Mute: TOP of board near Multi Track Bus
