MSSC Test Exam Questions And Answers Verified 100% Correct

MSSC Test Exam Questions And Answers Verified 100% Correct What is a revision number in the title block of a blueprint used for? - ANSWER Tracking each time there is a change to the drawing Where are revisions that are made to drawings tracked? - ANSWER Change block Which information is NOT included in a materials block? - ANSWER Revision number What information is provided by the basic surface finish symbol shown? - ANSWER Do not remove material How is a half scale drawing written? - ANSWER 1:2 What area on a drawing contains more information than print notes? - ANSWER Information block What two organizations set the standards for welding symbols? - ANSWER American National Standards Institute and American Welding Society The finish symbols and __________ symbols indicate how the weld should appear when the welding operation is complete. - ANSWER Contour __________ welds are used to connect two plates using holes in one or both plates to allow access for the welding tool. - ANSWER Plug and slot Which dimension would be placed directly to the right of a fillet weld symbol? - ANSWER Length Which weld symbol indicates a weld made by joining two members that overlap with one or both of the members having holes? - ANSWER Plug and slot A weld's contour is the shape of the weld's surface and can be everything below, EXCEPT __________. - ANSWER Round Which dimension is placed between the rays of a V-groove weld symbol? - ANSWER Groove angle The weld symbol for the other side is always on what side of the reference line? - ANSWER Top Which supplementary weld symbol consists of a circle placed around the joint where the reference line and the leader line meet? - ANSWER Weld-all-around The weld symbol __________. - ANSWER Indicates the type of weld the welder is to make What refers to tolerances that control form, profile, orientation, location, and runout? - ANSWER Geometric dimensioning and tolerancing Internal dimensions, like holes, are at their MMC when they are at their __________ of their tolerance zone? - ANSWER Lower limit In a feature control frame there is a symbol, a number, and a letter. What does the number represent? - ANSWER The total amount of tolerance for the geometric feature The basic dimensions shown on a print are called __________ dimensions. - ANSWER Nominal Which type of dimensioning uses a common reference point? - ANSWER Baseline dimensioning What is used to define parts based on how they function? - ANSWER Geometric dimensioning and tolerancing What is the difference between allowance and clearance? - ANSWER Allowance is the tightest possible fit, while clearance is the loosest possible fit If a product feature has a dimension of 1.8 ± .03, what is the lower tolerance dimension? - ANSWER 1.77 The specification for parts being produced at a workstation is 1.842 ± .005. Is a part that has been produced at 1.836 out of spec? - ANSWER Yes, it is out of spec Which type of fit is used when there is to be no movement between the parts? - ANSWER Interference fit A part measuring 44.85 mm in a process with a tolerance of 45mm +/- .28 is considered __________. - ANSWER In spec (within the tolerance range) How are datums identified on the process drawing? - ANSWER They are identified with a capital letter Which method of tolerancing places the tolerances next to each dimension? - ANSWER Direct 0.001 is __________. - ANSWER One thousandth Tolerance is the total amount by which a specified __________ is allowed to vary and still be a good part. - ANSWER Dimension What symbol means maximum material condition in geometric dimensioning and tolerancing? - ANSWER M in a circle What does the symbol below illustrate? - ANSWER Concentricity Of the five geometric features that are commonly toleranced, which describes the shape of a plane or circular type surface of a part? - ANSWER Form Which type of hole allows the head of a fastener to rest on a flat surface below the outer surface of the part? - ANSWER Counterbored Sixty minutes of arc is equivalent to how many degrees? - ANSWER 1 Identify the feature indicated by the arrow. - ANSWER Dimension line Which of the following drawing dimensioning guideline is incorrect? - ANSWER Include every possible dimension When the same type of arc is used in more than one place, what note is included with the dimension? - ANSWER Typical (TYP) What is a datum? - ANSWER Reference point Counterbore holes are best described by which of the following statements? - ANSWER A counterbore hole has an enlarged opening in the top