10/10/25, 9:24 AM NAO VOLUME 3 Exam fully solved & updated 2025-2026(latest version verified for accuracy) | 2024\2025Latest!! Flashcards | Qui…
NAO VOLUME 3 Exam fully solved & updated
2025-2026(latest version verified for accuracy) |
2024\2025Latest!!
Save
Terms in this set (105)
The correct transposed RX -1.50 + 0.50 x 127
for -1.00-.50x37 is?
The correct transposition Plano +2.00 x 150
for +2.00 -2.00 x 060 is?
An uncut lens must be at 60 mm
least _______ mm in diameter
to allow the edging of a
54 mm round lens
decentered 3 mm in:
A +3.00 sphere lens has a -3.25
front base curve of +6.25.
What is the back surface
curve?
A -2.00 -1.00 x 045 lens -8.25 -1.00
has a front base curve of
+6.25. What are the back
surface curves?
https://quizlet.com/1090641179/nao-volume-3-exam-fully-solved-updated-2025-2026latest-version-verified-for-accuracy-20242025latest-flash-cards/ 1/15
, 10/10/25, 9:24 AM NAO VOLUME 3 Exam fully solved & updated 2025-2026(latest version verified for accuracy) | 2024\2025Latest!! Flashcards | Qui…
Moving the optical center Base in prism
of a plus lens inward from
the correct PD results in
_____
Where will the optical To the left of the target center
center appear in a
lensometer when
neutralizing a left lens for
base in prism?
Glazing is a term used to A defect that occurs when an anti-reflective lens is
indicate _____ tinted
Frequently, bicentric up
grinding (slab-off) is used
as a means of obtaining
prism in the reading field
to correct induced prism
imbalance. The usual
correction during the
fabrication process is
achieved by grinding
prism in the following
direction:
A patient stops in to see Angle the temples upward from the end pieces
you for adjustment of his
glasses. After careful
inspection you find the
only thing wrong that
there is too much
pantoscopic tilt. To make
the necessary adjustment
you will:
https://quizlet.com/1090641179/nao-volume-3-exam-fully-solved-updated-2025-2026latest-version-verified-for-accuracy-20242025latest-flash-cards/ 2/15
NAO VOLUME 3 Exam fully solved & updated
2025-2026(latest version verified for accuracy) |
2024\2025Latest!!
Save
Terms in this set (105)
The correct transposed RX -1.50 + 0.50 x 127
for -1.00-.50x37 is?
The correct transposition Plano +2.00 x 150
for +2.00 -2.00 x 060 is?
An uncut lens must be at 60 mm
least _______ mm in diameter
to allow the edging of a
54 mm round lens
decentered 3 mm in:
A +3.00 sphere lens has a -3.25
front base curve of +6.25.
What is the back surface
curve?
A -2.00 -1.00 x 045 lens -8.25 -1.00
has a front base curve of
+6.25. What are the back
surface curves?
https://quizlet.com/1090641179/nao-volume-3-exam-fully-solved-updated-2025-2026latest-version-verified-for-accuracy-20242025latest-flash-cards/ 1/15
, 10/10/25, 9:24 AM NAO VOLUME 3 Exam fully solved & updated 2025-2026(latest version verified for accuracy) | 2024\2025Latest!! Flashcards | Qui…
Moving the optical center Base in prism
of a plus lens inward from
the correct PD results in
_____
Where will the optical To the left of the target center
center appear in a
lensometer when
neutralizing a left lens for
base in prism?
Glazing is a term used to A defect that occurs when an anti-reflective lens is
indicate _____ tinted
Frequently, bicentric up
grinding (slab-off) is used
as a means of obtaining
prism in the reading field
to correct induced prism
imbalance. The usual
correction during the
fabrication process is
achieved by grinding
prism in the following
direction:
A patient stops in to see Angle the temples upward from the end pieces
you for adjustment of his
glasses. After careful
inspection you find the
only thing wrong that
there is too much
pantoscopic tilt. To make
the necessary adjustment
you will:
https://quizlet.com/1090641179/nao-volume-3-exam-fully-solved-updated-2025-2026latest-version-verified-for-accuracy-20242025latest-flash-cards/ 2/15
