QUALITY ENGINEER EXAM - PART
2 2025 QUESTIONS AND ANSWERS
The audit team normally advises the auditee immediately upon the discovery of a
finding during an
audit. Which of the following items is (are) valid reasons for taking this action?
. If corrected immediately, the findings may be eliminated from the audit report.
. If corrected immediately, it shows genuine auditee interest in the objectives of the
audit.
. If corrected immediately, it demonstrates the strength of an ongoing audit program.
A. I only
B. IIIonly
C. IIandIIIonly
D. I,IIandIII - ....ANSWER ...-Answer: C
A purchase order for subassemblies classified as critical must include a review by
. Quality engineering.
. The procurement department.
...©️ 2025, ALL RIGHTS RESERVED 1
,. Design engineering.
A. IIIonly
B. I andIIIonly
C. IIandIIIonly
D. I,IIandIII - ....ANSWER ...-Answer: D
Which of the following are the MOST logical reasons for providing source inspection?
. The supplier has consistently shown poor out-going quality.
. The key inspection points are hidden after assembly at the suppliers' plant.
. The supplier requests the inspection to save them potential shipping expenses.
. The criticality of the product warrants it.
A. I,IIandIVonly
B. IIandIVonly
C. II,IIIandIVonly
D. I,II,IIIandIV - ....ANSWER ...-Answer: D
Inspection operations typically
A. Help in assuring satisfactory quality.
B. Reduce the usability of the product or service involved.
...©️ 2025, ALL RIGHTS RESERVED 2
, C. Require precise equipment in most instances.
D. Occur between all manufacturing operators. - ....ANSWER ...-Answer: A
Consider the following statement:
"A defect which might affect the appearance or general function of essential parts"
This definition describes a seriousness classification described as
A. Incidental.
B. Critical.
C. Minor.
D. Major. - ....ANSWER ...-Answer: D
Which of the following quality system provisions is of the greatest concern when
preparing an
audit checklist for a vendor qualification system audit?
A. Drawing and print control.
B. Makeup of the MRB
C. Training level of inspectors.
D. Calibration of test equipment. - ....ANSWER ...-Answer: D
In the planning of a new major manufacturing program, the greatest quality effort
should be put
...©️ 2025, ALL RIGHTS RESERVED 3
2 2025 QUESTIONS AND ANSWERS
The audit team normally advises the auditee immediately upon the discovery of a
finding during an
audit. Which of the following items is (are) valid reasons for taking this action?
. If corrected immediately, the findings may be eliminated from the audit report.
. If corrected immediately, it shows genuine auditee interest in the objectives of the
audit.
. If corrected immediately, it demonstrates the strength of an ongoing audit program.
A. I only
B. IIIonly
C. IIandIIIonly
D. I,IIandIII - ....ANSWER ...-Answer: C
A purchase order for subassemblies classified as critical must include a review by
. Quality engineering.
. The procurement department.
...©️ 2025, ALL RIGHTS RESERVED 1
,. Design engineering.
A. IIIonly
B. I andIIIonly
C. IIandIIIonly
D. I,IIandIII - ....ANSWER ...-Answer: D
Which of the following are the MOST logical reasons for providing source inspection?
. The supplier has consistently shown poor out-going quality.
. The key inspection points are hidden after assembly at the suppliers' plant.
. The supplier requests the inspection to save them potential shipping expenses.
. The criticality of the product warrants it.
A. I,IIandIVonly
B. IIandIVonly
C. II,IIIandIVonly
D. I,II,IIIandIV - ....ANSWER ...-Answer: D
Inspection operations typically
A. Help in assuring satisfactory quality.
B. Reduce the usability of the product or service involved.
...©️ 2025, ALL RIGHTS RESERVED 2
, C. Require precise equipment in most instances.
D. Occur between all manufacturing operators. - ....ANSWER ...-Answer: A
Consider the following statement:
"A defect which might affect the appearance or general function of essential parts"
This definition describes a seriousness classification described as
A. Incidental.
B. Critical.
C. Minor.
D. Major. - ....ANSWER ...-Answer: D
Which of the following quality system provisions is of the greatest concern when
preparing an
audit checklist for a vendor qualification system audit?
A. Drawing and print control.
B. Makeup of the MRB
C. Training level of inspectors.
D. Calibration of test equipment. - ....ANSWER ...-Answer: D
In the planning of a new major manufacturing program, the greatest quality effort
should be put
...©️ 2025, ALL RIGHTS RESERVED 3
