VIVINT SHP PRACTICE EXAM 130Q 2019 WITH COMPLETE
SOLUTIONS GUARANTEED PASS 2024-2025
True or false the fire fighter may be installed next to a
standalone battery powered smoke detector - ANSWER ->False
True or false when performing a full system test you may
bypass any open doors or windows - ANSWER ->False
When programming and SKEY1 you must: - ANSWER ->Always
enable the emergency key
True or false when running power to the take-345, polarity
does not matter - ANSWER ->False
Select all that apply when programming the emergency key for
SKEY1 one which zone/sensor types are recommended to use -
ANSWER ->Audible alarm 07 auxiliary alarm 08
True or false when installing a SMKT3 you must use the
included screws and anchors - ANSWER ->True
True or false when installing the fire fighter it is required to test
the customers existing smoke detectors - ANSWER ->True
When installing a DW 21 where is the approved location for the
sensor - ANSWER ->Between 6 inches (15cm) and 2 inches
(61cm) from the floor
, When installing a DW11 on a vinyl or metal frame what should
you primarily use to mount the sensor - ANSWER ->Provided
double-sided tape
Select all that apply which of the following materials can you
use to group multiple ground terminals in the takeover module
- ANSWER ->B connectors/beans and Wire caps
Which of the following sensors are not allowed to program
using a translator - ANSWER ->Smoke detector
True or false when installing the take 345 you must always test
the new 12 V battery before using it - ANSWER ->True
What is the output voltage of the transformer used to power
the Smart hub - ANSWER ->12 VDC
What is the minimum distance for placement of a CO3 from the
corners on a wall - ANSWER ->12 inches (30 cm)
True or false the SMK3 has only two functions: smoke and heat
detection - ANSWER ->False
How would you program a CO3 if mounted on a hallway wall -
ANSWER ->Loop 1, zone type 14
When installing a translator you must program all the existing
sensors as new equipment on the panel - ANSWER ->False
SOLUTIONS GUARANTEED PASS 2024-2025
True or false the fire fighter may be installed next to a
standalone battery powered smoke detector - ANSWER ->False
True or false when performing a full system test you may
bypass any open doors or windows - ANSWER ->False
When programming and SKEY1 you must: - ANSWER ->Always
enable the emergency key
True or false when running power to the take-345, polarity
does not matter - ANSWER ->False
Select all that apply when programming the emergency key for
SKEY1 one which zone/sensor types are recommended to use -
ANSWER ->Audible alarm 07 auxiliary alarm 08
True or false when installing a SMKT3 you must use the
included screws and anchors - ANSWER ->True
True or false when installing the fire fighter it is required to test
the customers existing smoke detectors - ANSWER ->True
When installing a DW 21 where is the approved location for the
sensor - ANSWER ->Between 6 inches (15cm) and 2 inches
(61cm) from the floor
, When installing a DW11 on a vinyl or metal frame what should
you primarily use to mount the sensor - ANSWER ->Provided
double-sided tape
Select all that apply which of the following materials can you
use to group multiple ground terminals in the takeover module
- ANSWER ->B connectors/beans and Wire caps
Which of the following sensors are not allowed to program
using a translator - ANSWER ->Smoke detector
True or false when installing the take 345 you must always test
the new 12 V battery before using it - ANSWER ->True
What is the output voltage of the transformer used to power
the Smart hub - ANSWER ->12 VDC
What is the minimum distance for placement of a CO3 from the
corners on a wall - ANSWER ->12 inches (30 cm)
True or false the SMK3 has only two functions: smoke and heat
detection - ANSWER ->False
How would you program a CO3 if mounted on a hallway wall -
ANSWER ->Loop 1, zone type 14
When installing a translator you must program all the existing
sensors as new equipment on the panel - ANSWER ->False
