ASE Certification Exam 2 Questions
With Correct Answers!!
All of the above
When using a scan tool to retrieve diagnostic trouble codes (DTCs) the technician should also
_________
Check monitor status
Check freeze frame data
Record any stored DTCs
All of the above
Relieve fuel system pressure before removing the fuel line connections
When replacing an external fuel filter, best practices include ________________
Use the same brand as the original as the replacement filter
Reuse the filter after cleaning
Relieve fuel system pressure before removing the fuel line connections
Tighten fasteners as tight as possible
Check for any stored diagnostic trouble codes
Before road testing a vehicle to determine if the automatic transmission is performing
normally, which should be performed?
Check for any stored diagnostic trouble codes
Check the fluid level
Check the fluid condition and color
All of the above
Between the transmission and the radiator
,Automatic transmission cooling lines are located ___________
Between the transmission and the radiator
Between the transmission and the rear axle
Inside the transmission or transaxle
Inside the HVAC module
To determine the fluid temperature
Why is a scan tool needed when checking the level of automatic transmission fluid?
To determine the fluid temperature
To check for any stored diagnostic trouble codes
To check which solenoids inside the transmission/transaxle are active
To determine the fluid capacity
Any of the above
Before replacing the filter in an automatic transmission/transaxle, why should
service information be checked first?
The filter may not be replaceable unless the unit is disassembled
The filter may be a spin-on type filter
The pan may be required to be removed
Any of the above
DOT 3 brake fluid or clutch fluid
To flush a hydraulic clutch system, what should be used?
DOT 3 brake fluid or clutch fluid
DOT 5 brake fluid
Solvent
Brake clean
, Any of the above
Service information should be Che led before replacing/adding manual transmission/transaxle
fluid because it can be ____________.
Automatic transmission fluid
Engine oil
Gear lube
Any of the above
Rubber or flexible plastic
CV joint boots should be carefully inspected during routine service because they are made from
_________ and can be torn or ripped allowing the grease to escape
Steel
Rubber or flexible plastic
Aluminum
Vinyl
Gear lube (usually SAE 80W-90)
Drive axle (differential case) fluid is usually ________
Engine oil (usually SAE 5W-30 or SAE 10W-30)
ATF
Gear lube (usually SAE 80W-90)
Any of the above
Any of the above are possible
Transfer case fluid is ______.
Engine oil (usually SAE 5W-30 or SAE 10W-30)
ATF
With Correct Answers!!
All of the above
When using a scan tool to retrieve diagnostic trouble codes (DTCs) the technician should also
_________
Check monitor status
Check freeze frame data
Record any stored DTCs
All of the above
Relieve fuel system pressure before removing the fuel line connections
When replacing an external fuel filter, best practices include ________________
Use the same brand as the original as the replacement filter
Reuse the filter after cleaning
Relieve fuel system pressure before removing the fuel line connections
Tighten fasteners as tight as possible
Check for any stored diagnostic trouble codes
Before road testing a vehicle to determine if the automatic transmission is performing
normally, which should be performed?
Check for any stored diagnostic trouble codes
Check the fluid level
Check the fluid condition and color
All of the above
Between the transmission and the radiator
,Automatic transmission cooling lines are located ___________
Between the transmission and the radiator
Between the transmission and the rear axle
Inside the transmission or transaxle
Inside the HVAC module
To determine the fluid temperature
Why is a scan tool needed when checking the level of automatic transmission fluid?
To determine the fluid temperature
To check for any stored diagnostic trouble codes
To check which solenoids inside the transmission/transaxle are active
To determine the fluid capacity
Any of the above
Before replacing the filter in an automatic transmission/transaxle, why should
service information be checked first?
The filter may not be replaceable unless the unit is disassembled
The filter may be a spin-on type filter
The pan may be required to be removed
Any of the above
DOT 3 brake fluid or clutch fluid
To flush a hydraulic clutch system, what should be used?
DOT 3 brake fluid or clutch fluid
DOT 5 brake fluid
Solvent
Brake clean
, Any of the above
Service information should be Che led before replacing/adding manual transmission/transaxle
fluid because it can be ____________.
Automatic transmission fluid
Engine oil
Gear lube
Any of the above
Rubber or flexible plastic
CV joint boots should be carefully inspected during routine service because they are made from
_________ and can be torn or ripped allowing the grease to escape
Steel
Rubber or flexible plastic
Aluminum
Vinyl
Gear lube (usually SAE 80W-90)
Drive axle (differential case) fluid is usually ________
Engine oil (usually SAE 5W-30 or SAE 10W-30)
ATF
Gear lube (usually SAE 80W-90)
Any of the above
Any of the above are possible
Transfer case fluid is ______.
Engine oil (usually SAE 5W-30 or SAE 10W-30)
ATF
