Mechanics Exam NEIEP Questions With
Complete Solutions 2025 | A+ Grade |Sure To
Pass !!
1. What is the name of the document that lists the hazards of a substance? -
ANSWER Material Safety Data Sheet or Safety Data Sheet
2. Who is responsible for making sure barricades are kept in place? - ANSWER
Everyone on the job
3. Who is primarily responsible for your safety on the job? - ANSWER You,
Yourself
4. Which agency guarantees your right to a safe workplace? - ANSWER OSHA
5. Which of the following is not a typical elevator repair? - ANSWER
6. Which of the following makes a good substitute for a ladder? - ANSWER
Never substitute anything
7. How should you proceed to et a toolbox to the machine room when climbing a
vertical ladder? - ANSWER Climb the ladder and pull the box up with a rope
8. What is the safest way to lubricate hoist ropes? - ANSWER With a rope
lubricator
,9. What supports a hydraulic elevator? - ANSWER The column of oil inside the
jack
10.What is the first thing you must do before performing any service on an
elevator - ANSWER Place barricades at the upper and lower ends
11.When a roller bearing needs to be pressed onto a shaft, what type of allowance
does the shaft have? - ANSWER Negative allowance
12.How are threads specified on metric bolts? - ANSWER
13.What is the tolerance accepted in the elevator industry? - ANSWER +- 1/64
14.What type of locking device uses a second nut run up against the first which
flattens when tightened? - ANSWER
15.How many possible views are there available from drawings using orthographic
projections? - ANSWER
16.Best Describe Layout Drawings - ANSWER A mechanical drawing showing
plans and elevation views of the elevator installation
17.What document provides information on the number of doors for an installation
and their color? - ANSWER Job Abstract
18.What is the purpose of the elevation view found in the final layouts? -
ANSWER To show vertical locations and dimensions of elevator components.
,19.The floor heights for the Wilton Towers are as follows; sub-basement- 10'2";
subbasement to basement-12'5"; basement to lobby-22'8"; lobby to the 11th
floor-120'5"; and to the executive floor-16'5". What is the total travel for an
elevator that travels from ht ebasement floor level to the executive floor level? -
ANSWER 159' 5"
20.DBG at the top-7' 11 5/32"
21.DBG at the bottom- 7' 10 17/64"
22.What is the difference? - ANSWER
23.You have been tasked with unloading 177 boxes from the company truck and
moving them into a storage area. By noon you have moved 103 boxes. What
percentage of the load has been moved? - ANSWER 58%
24.The counterweight must weigh 40% of the car capacity plus the weight of the
assembled car. If the assembled car weighs 3800 lbs. and has a capacity of
2500lbs. what must the counterweight weigh? - ANSWER 5100lbs
25.What is the most important piece of equipment you have when using a power
saw? - ANSWER Safety Glasses
26.When using a circular saw... - ANSWER The base is not adjustable for cutting
depth.
27.What functions can load weighing transducer perform - ANSWER Adjust door
times, bypass hall calls, and adjust motor control
28.What prevents manila rope from unraveling? - ANSWER Whipping
, 29.When using U-bolts... - ANSWER Place all U-bolt clips with the U shaped
portion bearing on the dead-end of the rope
30.Capstans should be - ANSWER fastened to building steel or other building
structure.
31.To interrupt hoisting on a capstan... - ANSWER ease off on the pulling rope
32.What type of wrench is used to align the holes for rail installation? - ANSWER
Spud Wrench
33.What wrench is used to thread pipes with polished surfaces together? -
ANSWER Strap Wrench
34.Hacksaw Blades - ANSWER must be installed with the teeth facing forward
35.Metal Ladders - ANSWER should never be used
36.Tension on the governor rope is maintained by using - ANSWER a tension
sheave
37.____ should not be disassembled in the field - ANSWER Oil Buffers
38.The loss of traction created between the hoist ropes and the machine driver
when the counterweight lands on its buffer avoids... - ANSWER The elevator
car being flung into the overhead
Complete Solutions 2025 | A+ Grade |Sure To
Pass !!
1. What is the name of the document that lists the hazards of a substance? -
ANSWER Material Safety Data Sheet or Safety Data Sheet
2. Who is responsible for making sure barricades are kept in place? - ANSWER
Everyone on the job
3. Who is primarily responsible for your safety on the job? - ANSWER You,
Yourself
4. Which agency guarantees your right to a safe workplace? - ANSWER OSHA
5. Which of the following is not a typical elevator repair? - ANSWER
6. Which of the following makes a good substitute for a ladder? - ANSWER
Never substitute anything
7. How should you proceed to et a toolbox to the machine room when climbing a
vertical ladder? - ANSWER Climb the ladder and pull the box up with a rope
8. What is the safest way to lubricate hoist ropes? - ANSWER With a rope
lubricator
,9. What supports a hydraulic elevator? - ANSWER The column of oil inside the
jack
10.What is the first thing you must do before performing any service on an
elevator - ANSWER Place barricades at the upper and lower ends
11.When a roller bearing needs to be pressed onto a shaft, what type of allowance
does the shaft have? - ANSWER Negative allowance
12.How are threads specified on metric bolts? - ANSWER
13.What is the tolerance accepted in the elevator industry? - ANSWER +- 1/64
14.What type of locking device uses a second nut run up against the first which
flattens when tightened? - ANSWER
15.How many possible views are there available from drawings using orthographic
projections? - ANSWER
16.Best Describe Layout Drawings - ANSWER A mechanical drawing showing
plans and elevation views of the elevator installation
17.What document provides information on the number of doors for an installation
and their color? - ANSWER Job Abstract
18.What is the purpose of the elevation view found in the final layouts? -
ANSWER To show vertical locations and dimensions of elevator components.
,19.The floor heights for the Wilton Towers are as follows; sub-basement- 10'2";
subbasement to basement-12'5"; basement to lobby-22'8"; lobby to the 11th
floor-120'5"; and to the executive floor-16'5". What is the total travel for an
elevator that travels from ht ebasement floor level to the executive floor level? -
ANSWER 159' 5"
20.DBG at the top-7' 11 5/32"
21.DBG at the bottom- 7' 10 17/64"
22.What is the difference? - ANSWER
23.You have been tasked with unloading 177 boxes from the company truck and
moving them into a storage area. By noon you have moved 103 boxes. What
percentage of the load has been moved? - ANSWER 58%
24.The counterweight must weigh 40% of the car capacity plus the weight of the
assembled car. If the assembled car weighs 3800 lbs. and has a capacity of
2500lbs. what must the counterweight weigh? - ANSWER 5100lbs
25.What is the most important piece of equipment you have when using a power
saw? - ANSWER Safety Glasses
26.When using a circular saw... - ANSWER The base is not adjustable for cutting
depth.
27.What functions can load weighing transducer perform - ANSWER Adjust door
times, bypass hall calls, and adjust motor control
28.What prevents manila rope from unraveling? - ANSWER Whipping
, 29.When using U-bolts... - ANSWER Place all U-bolt clips with the U shaped
portion bearing on the dead-end of the rope
30.Capstans should be - ANSWER fastened to building steel or other building
structure.
31.To interrupt hoisting on a capstan... - ANSWER ease off on the pulling rope
32.What type of wrench is used to align the holes for rail installation? - ANSWER
Spud Wrench
33.What wrench is used to thread pipes with polished surfaces together? -
ANSWER Strap Wrench
34.Hacksaw Blades - ANSWER must be installed with the teeth facing forward
35.Metal Ladders - ANSWER should never be used
36.Tension on the governor rope is maintained by using - ANSWER a tension
sheave
37.____ should not be disassembled in the field - ANSWER Oil Buffers
38.The loss of traction created between the hoist ropes and the machine driver
when the counterweight lands on its buffer avoids... - ANSWER The elevator
car being flung into the overhead
