RESIDENTAL PLUMBING OVERVIEW FOR
INPECTORS COURSE WITH CORRECT QUESTION
AND ACTUAL ANSWERS GRADED A+.
THIS ---- A CODE COMPLIANCE COURSE OF PLUMBING - ANSWERS-IS NOT
------- DRAINAGE FITTINGS ARE DESIGED WITH PATTERNS WHICH PROVIDE AT
LEAST RESISTANCE TO FLOW - ANSWERS-SOME
STORM WATER, RAIN WATER AND GROUNDWATER ----- BE DRAINED INTO THE
SEWER SYSTEM - ANSWERS-SHOULD NOT
DISCHARGING UNTREATED SWEAGE OR WASTEWATER ONTO THE GROUNDS
SURGACE ------- PERMISSIBLE - ANSWERS-IS NOT
A RELIEF-VALVE PIPE TERMINATING INTO A WATER LEAK CATCH PAN ---
PERMITTED BECAUSE THE PAN IS NOT AN INDIRECT WASTE RECEPTOR -
ANSWERS-IS NOT
3/4 INCH IS THE ----- DIAMETER OF A WATER SERVICE PIPE - ANSWERS-MINIMUM
WHAT MATERIA ARE WATER CLOSET BOLTS OFTEN MADE OUT OF DUE TO
CORROSION RESISTANCE - ANSWERS-BRASS
THE---- CONNECTOR SHOULD ENTER AT THE HIGHEST LEVEL WHERE TWO OR
MORE VENT CONNECTORS ENTER A COMMON GAS VENT, CHIMNEY FLUE OR
SINGLE WALL METAL PIPE - ANSWERS-SMALLEST
OLD TAILPIECES AND TRAPS MADE OF ---- SOFT BRASS ARE SOMETIMES SO THIN
THAT A GENTLE TOUCH WILL CAUSE THEM TO BREAK INTO PIECES IN YOUR HAND
- ANSWERS-SOFT BRASS
THE TERMINATION FOR GAS VENT PIPES FOR ROOFS HAVING A PITCH OF UP TO
6:12 NEEDS TO BE ---- HIGH - ANSWERS-1 FOOT
,---WATER HEATERS SHOULD NOT OBTAIN COMBUSTION AIR FROM SLEEPING
ROOMS, BATHRROMS OR TOILETS - ANSWERS-FUEL-FIRED
THE HORIZONTAL SPACING FOR SUPPORTING PIPE MADE OF CAST IRON SHOULD
BE A MAXIMUM OF ---- FEET - ANSWERS-5
TRAPS THAT IMPEDE DRAINAGE FLOW, SUCH AS ---TRAPS, ARE NOT PERMITTED -
ANSWERS-DRUM AND S-
TYPIICALY USED FOR UNDERGROUND WATER SERVICE, IS TYPE K COPPER
TUBING WHICH IS THE ----A - ANSWERS-THICKEST
TRAPS ARE PROTECTED FROM SIPHONAGE BY WHAT? - ANSWERS-AIR
ADMITTANCE VALVES
A ---- IS REFERRED TO IN THE PLUMBING STANDARDS AS WATER CLOSET -
ANSWERS-TOILET
1/8 INCH PER FOOT IS THE ------- SLOPE REQUIRED FOR A HORIONTAL DRAIN PIPE
THAT IS SIZED BETWEN 3 AND 6 INCHES - ANSWERS-MINIMUM
THE INSPECTOR ---- REQUIRED TO FLUSH ALL OF THE TOILETS - ANSWERS-IS
A ---- IS DEFINED AS A LOCATION WHERE APPLIANCE/EQUIPMENT IS LOCATED
THAT IS NOT GREATER THAN 50 CUBIC FEET PER 1000 BTU/H (4.83 L/W) OF
AGGREGATE INPUT RATING OF THE APPLIANCE/EQUIPMENT - ANSWERS-
CONFINED SPACE
SOLVENT-CEMENTING JOINTS BETWEEN DIFFERENT TYPES OF PLASTIC IS NOT
ALLOWED BECAUSE THE CHEMICAL COMPOSITION OF THE JOINT WILL NOT BE -
ANSWERS-HOMOGENEOUS
ELECTRIC DISCONNECTS ARE REQUIRED FOR ALL ELECTRIC ---- - ANSWERS-
WATER HEATERS
INSPECTORS ARE NOT REQUIRED TO DETERMINE THE EXISTENCE OF ----
PLUMBING IN A HOME - ANSWERS-POLYBUTYLENETHIS ---- A CODE COMPLIANCE
COURSE OF PLUMBING - ANSWERS-IS NOT
, ------- DRAINAGE FITTINGS ARE DESIGED WITH PATTERNS WHICH PROVIDE AT
LEAST RESISTANCE TO FLOW - ANSWERS-SOME
STORM WATER, RAIN WATER AND GROUNDWATER ----- BE DRAINED INTO THE
SEWER SYSTEM - ANSWERS-SHOULD NOT
DISCHARGING UNTREATED SWEAGE OR WASTEWATER ONTO THE GROUNDS
SURGACE ------- PERMISSIBLE - ANSWERS-IS NOT
A RELIEF-VALVE PIPE TERMINATING INTO A WATER LEAK CATCH PAN ---
PERMITTED BECAUSE THE PAN IS NOT AN INDIRECT WASTE RECEPTOR -
ANSWERS-IS NOT
3/4 INCH IS THE ----- DIAMETER OF A WATER SERVICE PIPE - ANSWERS-MINIMUM
WHAT MATERIA ARE WATER CLOSET BOLTS OFTEN MADE OUT OF DUE TO
CORROSION RESISTANCE - ANSWERS-BRASS
THE---- CONNECTOR SHOULD ENTER AT THE HIGHEST LEVEL WHERE TWO OR
MORE VENT CONNECTORS ENTER A COMMON GAS VENT, CHIMNEY FLUE OR
SINGLE WALL METAL PIPE - ANSWERS-SMALLEST
OLD TAILPIECES AND TRAPS MADE OF ---- SOFT BRASS ARE SOMETIMES SO THIN
THAT A GENTLE TOUCH WILL CAUSE THEM TO BREAK INTO PIECES IN YOUR HAND
- ANSWERS-SOFT BRASS
THE TERMINATION FOR GAS VENT PIPES FOR ROOFS HAVING A PITCH OF UP TO
6:12 NEEDS TO BE ---- HIGH - ANSWERS-1 FOOT
---WATER HEATERS SHOULD NOT OBTAIN COMBUSTION AIR FROM SLEEPING
ROOMS, BATHRROMS OR TOILETS - ANSWERS-FUEL-FIRED
THE HORIZONTAL SPACING FOR SUPPORTING PIPE MADE OF CAST IRON SHOULD
BE A MAXIMUM OF ---- FEET - ANSWERS-5
TRAPS THAT IMPEDE DRAINAGE FLOW, SUCH AS ---TRAPS, ARE NOT PERMITTED -
ANSWERS-DRUM AND S-
INPECTORS COURSE WITH CORRECT QUESTION
AND ACTUAL ANSWERS GRADED A+.
THIS ---- A CODE COMPLIANCE COURSE OF PLUMBING - ANSWERS-IS NOT
------- DRAINAGE FITTINGS ARE DESIGED WITH PATTERNS WHICH PROVIDE AT
LEAST RESISTANCE TO FLOW - ANSWERS-SOME
STORM WATER, RAIN WATER AND GROUNDWATER ----- BE DRAINED INTO THE
SEWER SYSTEM - ANSWERS-SHOULD NOT
DISCHARGING UNTREATED SWEAGE OR WASTEWATER ONTO THE GROUNDS
SURGACE ------- PERMISSIBLE - ANSWERS-IS NOT
A RELIEF-VALVE PIPE TERMINATING INTO A WATER LEAK CATCH PAN ---
PERMITTED BECAUSE THE PAN IS NOT AN INDIRECT WASTE RECEPTOR -
ANSWERS-IS NOT
3/4 INCH IS THE ----- DIAMETER OF A WATER SERVICE PIPE - ANSWERS-MINIMUM
WHAT MATERIA ARE WATER CLOSET BOLTS OFTEN MADE OUT OF DUE TO
CORROSION RESISTANCE - ANSWERS-BRASS
THE---- CONNECTOR SHOULD ENTER AT THE HIGHEST LEVEL WHERE TWO OR
MORE VENT CONNECTORS ENTER A COMMON GAS VENT, CHIMNEY FLUE OR
SINGLE WALL METAL PIPE - ANSWERS-SMALLEST
OLD TAILPIECES AND TRAPS MADE OF ---- SOFT BRASS ARE SOMETIMES SO THIN
THAT A GENTLE TOUCH WILL CAUSE THEM TO BREAK INTO PIECES IN YOUR HAND
- ANSWERS-SOFT BRASS
THE TERMINATION FOR GAS VENT PIPES FOR ROOFS HAVING A PITCH OF UP TO
6:12 NEEDS TO BE ---- HIGH - ANSWERS-1 FOOT
,---WATER HEATERS SHOULD NOT OBTAIN COMBUSTION AIR FROM SLEEPING
ROOMS, BATHRROMS OR TOILETS - ANSWERS-FUEL-FIRED
THE HORIZONTAL SPACING FOR SUPPORTING PIPE MADE OF CAST IRON SHOULD
BE A MAXIMUM OF ---- FEET - ANSWERS-5
TRAPS THAT IMPEDE DRAINAGE FLOW, SUCH AS ---TRAPS, ARE NOT PERMITTED -
ANSWERS-DRUM AND S-
TYPIICALY USED FOR UNDERGROUND WATER SERVICE, IS TYPE K COPPER
TUBING WHICH IS THE ----A - ANSWERS-THICKEST
TRAPS ARE PROTECTED FROM SIPHONAGE BY WHAT? - ANSWERS-AIR
ADMITTANCE VALVES
A ---- IS REFERRED TO IN THE PLUMBING STANDARDS AS WATER CLOSET -
ANSWERS-TOILET
1/8 INCH PER FOOT IS THE ------- SLOPE REQUIRED FOR A HORIONTAL DRAIN PIPE
THAT IS SIZED BETWEN 3 AND 6 INCHES - ANSWERS-MINIMUM
THE INSPECTOR ---- REQUIRED TO FLUSH ALL OF THE TOILETS - ANSWERS-IS
A ---- IS DEFINED AS A LOCATION WHERE APPLIANCE/EQUIPMENT IS LOCATED
THAT IS NOT GREATER THAN 50 CUBIC FEET PER 1000 BTU/H (4.83 L/W) OF
AGGREGATE INPUT RATING OF THE APPLIANCE/EQUIPMENT - ANSWERS-
CONFINED SPACE
SOLVENT-CEMENTING JOINTS BETWEEN DIFFERENT TYPES OF PLASTIC IS NOT
ALLOWED BECAUSE THE CHEMICAL COMPOSITION OF THE JOINT WILL NOT BE -
ANSWERS-HOMOGENEOUS
ELECTRIC DISCONNECTS ARE REQUIRED FOR ALL ELECTRIC ---- - ANSWERS-
WATER HEATERS
INSPECTORS ARE NOT REQUIRED TO DETERMINE THE EXISTENCE OF ----
PLUMBING IN A HOME - ANSWERS-POLYBUTYLENETHIS ---- A CODE COMPLIANCE
COURSE OF PLUMBING - ANSWERS-IS NOT
, ------- DRAINAGE FITTINGS ARE DESIGED WITH PATTERNS WHICH PROVIDE AT
LEAST RESISTANCE TO FLOW - ANSWERS-SOME
STORM WATER, RAIN WATER AND GROUNDWATER ----- BE DRAINED INTO THE
SEWER SYSTEM - ANSWERS-SHOULD NOT
DISCHARGING UNTREATED SWEAGE OR WASTEWATER ONTO THE GROUNDS
SURGACE ------- PERMISSIBLE - ANSWERS-IS NOT
A RELIEF-VALVE PIPE TERMINATING INTO A WATER LEAK CATCH PAN ---
PERMITTED BECAUSE THE PAN IS NOT AN INDIRECT WASTE RECEPTOR -
ANSWERS-IS NOT
3/4 INCH IS THE ----- DIAMETER OF A WATER SERVICE PIPE - ANSWERS-MINIMUM
WHAT MATERIA ARE WATER CLOSET BOLTS OFTEN MADE OUT OF DUE TO
CORROSION RESISTANCE - ANSWERS-BRASS
THE---- CONNECTOR SHOULD ENTER AT THE HIGHEST LEVEL WHERE TWO OR
MORE VENT CONNECTORS ENTER A COMMON GAS VENT, CHIMNEY FLUE OR
SINGLE WALL METAL PIPE - ANSWERS-SMALLEST
OLD TAILPIECES AND TRAPS MADE OF ---- SOFT BRASS ARE SOMETIMES SO THIN
THAT A GENTLE TOUCH WILL CAUSE THEM TO BREAK INTO PIECES IN YOUR HAND
- ANSWERS-SOFT BRASS
THE TERMINATION FOR GAS VENT PIPES FOR ROOFS HAVING A PITCH OF UP TO
6:12 NEEDS TO BE ---- HIGH - ANSWERS-1 FOOT
---WATER HEATERS SHOULD NOT OBTAIN COMBUSTION AIR FROM SLEEPING
ROOMS, BATHRROMS OR TOILETS - ANSWERS-FUEL-FIRED
THE HORIZONTAL SPACING FOR SUPPORTING PIPE MADE OF CAST IRON SHOULD
BE A MAXIMUM OF ---- FEET - ANSWERS-5
TRAPS THAT IMPEDE DRAINAGE FLOW, SUCH AS ---TRAPS, ARE NOT PERMITTED -
ANSWERS-DRUM AND S-
