SHP Final Exam Questions
The firefighter may be installed next to a stand-alone battery smoke detector - ANS-
True
When performing a full system test, you may bypass any open doors or windows - ANS-
False
When programming an skey1,you must - ANS-Always enable the emergency
When running power to the take345,polarity doesn't apply - ANS-False
When programming the emergency key for the skey1,which zone/sensor type is used. -
ANS-Audible alarm (7)
When installing a smkt3,you must use the included screws and anchors - ANS-True
When installing the firefighter, it is required to test the customers existing smoke
detectors - ANS-True
When installing a Dw21, where is the approved location for the sensor - ANS-Between
6"(15cm) and 2'(61cm) from floor
When installing a dw11 on a vinyl or metal frame, what should primarily use to mount
the sensor - ANS-Provided double sided tape
Which of the following materials can you use to group multiple ground terminals in a
takeover. - ANS-Beans & wire caps
Which of the following sensors are you not allowed to program using a translator - ANS-
Smoke detector
When installing the take345, you must always test the new 12v battery before using it. -
ANS-True
What is the output voltage of transformer used to power the sky control - ANS-16.5
What is the minimum distance for placement of a co3 from the corners of the wall -
ANS-12"
The smkt3 has 2 function:smoke and heat detection - ANS-False
How would you program a co3 if mounted on a hallway wall - ANS-Loop 1 Zone 14
, When installing a translator, you must program all of the existing sensors as new
equipment on the panel - ANS-False
The dw21 should always be installed in the door frame - ANS-True
Which of the following zone/sensor types are correct when programming an smkt3 -
ANS-(09) Smoke detector. (09) Heat detector. (08) Freeze
What it the correct height ar which to install the Pir2 - ANS-7ft
When programming a Dw21 what loop number is used - ANS-Loop 2
When programming a sensor into a sky control panel, you can type in the serial number
or learn it in by triggering the device. - ANS-True
How would you program a gb2 when it is mounted on a master bedroom ceiling - ANS-
Loop 1 Zone 3
Panic pendants are programmed as an audible alarm(type 07) - ANS-True
When installing the take 345 you must ensure that the transformer is supplying power to
the power supply before connecting the battery - ANS-True
When wiring the take 345 you must ensure it has three points of ground: the low side of
each zone, the takeover module, and the power supply - ANS-True
You are required to test all secondary keypads and key fobs even though they are not
detection devices - ANS-True
When installing a dw21, what size drill bit should you use to drill the hole for the sensor -
ANS-3/4"
When programming a Pir2, which loop number must you use - ANS-Loop 1
Which step should you always take to ensure that the z wave network is aligned in the
strongest manner? - ANS-
When powering up a deadbolt smart lock for the first time, which of the following must
you always do - ANS-Initiate the lock handling procedure
When installing a deadbolt smart lock, insert the wiring harness below below the bolt -
ANS-True
What is the input voltage range for a doorbell camera - ANS-12-24v
The firefighter may be installed next to a stand-alone battery smoke detector - ANS-
True
When performing a full system test, you may bypass any open doors or windows - ANS-
False
When programming an skey1,you must - ANS-Always enable the emergency
When running power to the take345,polarity doesn't apply - ANS-False
When programming the emergency key for the skey1,which zone/sensor type is used. -
ANS-Audible alarm (7)
When installing a smkt3,you must use the included screws and anchors - ANS-True
When installing the firefighter, it is required to test the customers existing smoke
detectors - ANS-True
When installing a Dw21, where is the approved location for the sensor - ANS-Between
6"(15cm) and 2'(61cm) from floor
When installing a dw11 on a vinyl or metal frame, what should primarily use to mount
the sensor - ANS-Provided double sided tape
Which of the following materials can you use to group multiple ground terminals in a
takeover. - ANS-Beans & wire caps
Which of the following sensors are you not allowed to program using a translator - ANS-
Smoke detector
When installing the take345, you must always test the new 12v battery before using it. -
ANS-True
What is the output voltage of transformer used to power the sky control - ANS-16.5
What is the minimum distance for placement of a co3 from the corners of the wall -
ANS-12"
The smkt3 has 2 function:smoke and heat detection - ANS-False
How would you program a co3 if mounted on a hallway wall - ANS-Loop 1 Zone 14
, When installing a translator, you must program all of the existing sensors as new
equipment on the panel - ANS-False
The dw21 should always be installed in the door frame - ANS-True
Which of the following zone/sensor types are correct when programming an smkt3 -
ANS-(09) Smoke detector. (09) Heat detector. (08) Freeze
What it the correct height ar which to install the Pir2 - ANS-7ft
When programming a Dw21 what loop number is used - ANS-Loop 2
When programming a sensor into a sky control panel, you can type in the serial number
or learn it in by triggering the device. - ANS-True
How would you program a gb2 when it is mounted on a master bedroom ceiling - ANS-
Loop 1 Zone 3
Panic pendants are programmed as an audible alarm(type 07) - ANS-True
When installing the take 345 you must ensure that the transformer is supplying power to
the power supply before connecting the battery - ANS-True
When wiring the take 345 you must ensure it has three points of ground: the low side of
each zone, the takeover module, and the power supply - ANS-True
You are required to test all secondary keypads and key fobs even though they are not
detection devices - ANS-True
When installing a dw21, what size drill bit should you use to drill the hole for the sensor -
ANS-3/4"
When programming a Pir2, which loop number must you use - ANS-Loop 1
Which step should you always take to ensure that the z wave network is aligned in the
strongest manner? - ANS-
When powering up a deadbolt smart lock for the first time, which of the following must
you always do - ANS-Initiate the lock handling procedure
When installing a deadbolt smart lock, insert the wiring harness below below the bolt -
ANS-True
What is the input voltage range for a doorbell camera - ANS-12-24v
