Virginia hic Exam Questions with correct Answers
The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs
is - ANSWER- 1 1/4 inches
What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-
5,400 pounds
What is the MINIMUM clearance that combustible insulation MUST other heat-
producing devices - ANSWER- 1 inch
What is the MAXIMUM flame spread index for insulation materials - ANSWER- 25
The amount of water per sack of cement is what controls all EXCEPT - ANSWER- Wear
resistance
The escape device for a trench over 4 feet deep MUST be within a MAXIMUM of -
ANSWER- 25 feet of the worker
What is the correct sequence for installing a bi-fold door - ANSWER- Top track, lower
track, insert bottom pivot, insert upper pivot
What is the MINIMUM height for a stairway handrail - ANSWER- 34 inches
How MUST rafters be framed to each other - ANSWER- With rectangular ties
The nailing holes in aluminum and vinyl siding are elongated to allow for - ANSWER-
Expansion and contraction
What are batter boards - ANSWER- stakes and ledger boards marking building lines
The first step that needs to be taken prior to starting any excavation work is - ANSWER-
contracting the local utility companies
What is the MAXIMUM distance horizontal reinforcement can be placed from the top of
a masonry partition wall - ANSWER- 16 inches
What is the MINIMUM vertical reinforcement spacing for a reinforced concrete
foundation wall that is 7 feet high and 10 inches thick on type SP soil - ANSWER- 48
inches on center
, A third stairway stringer should be used when the stair width exceeds - ANSWER- 30
inches
Unless otherwise specified, the standard guideline for spacing contraction joints is to
space them in feet - ANSWER- 2 times the stab depth in inches
What is the MINIMUM lap of riveted horizontal lap siding - ANSWER- 1 inches
For multiple-width masonry (mampostería de ancho múltiple) what is the MINIMUM
thickness of grout between masonry units and reinforcements? - ANSWER- 1/4 inch
What is the MAXIMUM dimension of the ventilation coverings for under-floor space -
ANSWER- 1/4 inch
The MOST specific information about the size and location of windows would be found
in a - ANSWER- Floor plan
What is the MINIMUM illumination for general constructions area lighting - ANSWER- 5
foot candles
in drywall 3 trim is used to - ANSWER- provide a finish edge
What is the MINIMUM number of anchor bolts REQUIRED for anchoring a 12 foot
section of wood still plate to a foundation - ANSWER- two bolts
What is the MINIMUM square footage of net clear opening area for an egress window in
a second floor sleeping area - ANSWER- 5.70 square feet
Which window type consists of an upper and a lower sash that slide vertically in the side
jambs - ANSWER- Double hung windows
Damp proofing on below-grade masonry foundation walls shall extend from the top of
the footing to - ANSWER- 6 inches above the finished grade
Scaffolds MUST remain a MINIMUM of how many feet from a 50-kV power line -
ANSWER- 10 feet
The REQUIREMENT for the thickness of masonry unit bed joints for the second course
shall be - ANSWER- 3/8 inches
The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs
is - ANSWER- 1 1/4 inches
What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-
5,400 pounds
What is the MINIMUM clearance that combustible insulation MUST other heat-
producing devices - ANSWER- 1 inch
What is the MAXIMUM flame spread index for insulation materials - ANSWER- 25
The amount of water per sack of cement is what controls all EXCEPT - ANSWER- Wear
resistance
The escape device for a trench over 4 feet deep MUST be within a MAXIMUM of -
ANSWER- 25 feet of the worker
What is the correct sequence for installing a bi-fold door - ANSWER- Top track, lower
track, insert bottom pivot, insert upper pivot
What is the MINIMUM height for a stairway handrail - ANSWER- 34 inches
How MUST rafters be framed to each other - ANSWER- With rectangular ties
The nailing holes in aluminum and vinyl siding are elongated to allow for - ANSWER-
Expansion and contraction
What are batter boards - ANSWER- stakes and ledger boards marking building lines
The first step that needs to be taken prior to starting any excavation work is - ANSWER-
contracting the local utility companies
What is the MAXIMUM distance horizontal reinforcement can be placed from the top of
a masonry partition wall - ANSWER- 16 inches
What is the MINIMUM vertical reinforcement spacing for a reinforced concrete
foundation wall that is 7 feet high and 10 inches thick on type SP soil - ANSWER- 48
inches on center
, A third stairway stringer should be used when the stair width exceeds - ANSWER- 30
inches
Unless otherwise specified, the standard guideline for spacing contraction joints is to
space them in feet - ANSWER- 2 times the stab depth in inches
What is the MINIMUM lap of riveted horizontal lap siding - ANSWER- 1 inches
For multiple-width masonry (mampostería de ancho múltiple) what is the MINIMUM
thickness of grout between masonry units and reinforcements? - ANSWER- 1/4 inch
What is the MAXIMUM dimension of the ventilation coverings for under-floor space -
ANSWER- 1/4 inch
The MOST specific information about the size and location of windows would be found
in a - ANSWER- Floor plan
What is the MINIMUM illumination for general constructions area lighting - ANSWER- 5
foot candles
in drywall 3 trim is used to - ANSWER- provide a finish edge
What is the MINIMUM number of anchor bolts REQUIRED for anchoring a 12 foot
section of wood still plate to a foundation - ANSWER- two bolts
What is the MINIMUM square footage of net clear opening area for an egress window in
a second floor sleeping area - ANSWER- 5.70 square feet
Which window type consists of an upper and a lower sash that slide vertically in the side
jambs - ANSWER- Double hung windows
Damp proofing on below-grade masonry foundation walls shall extend from the top of
the footing to - ANSWER- 6 inches above the finished grade
Scaffolds MUST remain a MINIMUM of how many feet from a 50-kV power line -
ANSWER- 10 feet
The REQUIREMENT for the thickness of masonry unit bed joints for the second course
shall be - ANSWER- 3/8 inches
