NCCER MILLWRIGHT PRACTICE EXAM 2
Study online at https://quizlet.com/_9meswr
1. If the seal was not properly aligned or there is ex- unusual
cessive wear in some bearing or shaft,_______ wear
tracks will be the indicator
2. For removing hard to remove gasket materials sharpened brass putty knife
found on sealing surfaces, ______ is recommended
3. Apprenticeship training is_______ Conducted on the job
4. Charting alignment on a graph requires a chart distance
that is divided into thousandths of an inch vertically
for the indicator readings and into whole inches
horizontally for the__________
5. The orthographic drawing may contain a dashed or hidden
_______ line
6. In order to shoot through a test object and project Radiation
an image onto a detector or a sheet of film, radiog-
raphy uses a source of penetrating called _______
7. Which of the following task would you not perform *scribe circles
with dividers? *transfer measurements
*compare distances
<measure angles
8. The over speed trip device is actuated when the 10%
turbine reaches a predetermined limit usually
_________% above normal full-load speed
9. Positive results in an offset measurement mean high
that the MTBM is _____ or on the 3-o'clock side.
10. offset misalignment
, NCCER MILLWRIGHT PRACTICE EXAM 2
Study online at https://quizlet.com/_9meswr
The coupling gap is set, and then the ______ is mea-
sured
11. In a hydraulic system, movement depends on_____ pressure
12. Fractional dimensions are used on objects such as furniture or utility items
_______ or ______
13. If the cause of the problem is not immediately un- elimination
derstood, the process of________is often the proce-
dure of choice
14. When applying sealant to the sealing gland 3/16
flanges, keep the sealant away from the inside
edges of the flange by at least_______ inch
15. A stroboscope is triggered by a_______ Transducer
16. The pitch of threaded fasteners is measured with a thread
________gauge
17. Liquid penetrant highlights flaws and re- Surface cracks
veals________
18. A tool used to cut external threats on s bolt or rod die
is called a ______
19. A bill of materials may include info on _______ and special processes
other reference information
20. Engaged gears always have the same _____ surface speed
21. Elevation of equipment is usually found in the_____ general arrangement
22. Vibrations
Study online at https://quizlet.com/_9meswr
1. If the seal was not properly aligned or there is ex- unusual
cessive wear in some bearing or shaft,_______ wear
tracks will be the indicator
2. For removing hard to remove gasket materials sharpened brass putty knife
found on sealing surfaces, ______ is recommended
3. Apprenticeship training is_______ Conducted on the job
4. Charting alignment on a graph requires a chart distance
that is divided into thousandths of an inch vertically
for the indicator readings and into whole inches
horizontally for the__________
5. The orthographic drawing may contain a dashed or hidden
_______ line
6. In order to shoot through a test object and project Radiation
an image onto a detector or a sheet of film, radiog-
raphy uses a source of penetrating called _______
7. Which of the following task would you not perform *scribe circles
with dividers? *transfer measurements
*compare distances
<measure angles
8. The over speed trip device is actuated when the 10%
turbine reaches a predetermined limit usually
_________% above normal full-load speed
9. Positive results in an offset measurement mean high
that the MTBM is _____ or on the 3-o'clock side.
10. offset misalignment
, NCCER MILLWRIGHT PRACTICE EXAM 2
Study online at https://quizlet.com/_9meswr
The coupling gap is set, and then the ______ is mea-
sured
11. In a hydraulic system, movement depends on_____ pressure
12. Fractional dimensions are used on objects such as furniture or utility items
_______ or ______
13. If the cause of the problem is not immediately un- elimination
derstood, the process of________is often the proce-
dure of choice
14. When applying sealant to the sealing gland 3/16
flanges, keep the sealant away from the inside
edges of the flange by at least_______ inch
15. A stroboscope is triggered by a_______ Transducer
16. The pitch of threaded fasteners is measured with a thread
________gauge
17. Liquid penetrant highlights flaws and re- Surface cracks
veals________
18. A tool used to cut external threats on s bolt or rod die
is called a ______
19. A bill of materials may include info on _______ and special processes
other reference information
20. Engaged gears always have the same _____ surface speed
21. Elevation of equipment is usually found in the_____ general arrangement
22. Vibrations
