During the inspection process, restorers shall make a reasonable effort to
(A) remove the excess water
(B) check for moisture in walls
(C) identify and address potential safety hazards
(D) eliminate possible furniture staining and damage
(C) identify and address potential safety hazards
A significant amount of water absorption and evaporation load where wet porous materials
represent ~5% to ~40% of combined ceiling, walls, and flooring surface areas and where low
evaporation materials and assemblies are minimally wet is
(A) class 1
(B) class 2
(C) class 3
(D) class 4
(B) class 2
Multiple extractions of salvageable materials, especially porous material (carpet, cushion),
often are required to
(A) eliminate potential microbial growth
(B) decrease drying time
(C) eliminate the need for antimicrobial (biocide) application
(D) increase the need for additional dehumidification
To enhance drying, restorers should manage both ambient temperature and.
(A) surface temperatures of affected materials
(B)outside temperatures of building envelopes
,(C) dehumidifier process output temperatures
, (D) output temperatures of the airmovers
(A) surface temperature of affected materials
Water damage restoration services should not begin until after the
(A) damage survey has been submitted
(B) restorer has entered into an adequately written contract
(C) insurance adjuster authorizes the work
(D) insurance policy has been reviewed and explained
(B) restorer has entered into an adequately written contract
Two tools that should be used properly disengage most stretched-in carpet are
(A) pliers and staple remover
(B) power stretcher and knee kicker
(C) knee kicker and carpet awl.
(D) base molding lifter and carpet awl
(C) knee kicker and carpet awl
When inspecting a water-damaged structure, restorers should inspect
(A) with thermal imaging camera to show definite areas of water
(B) only where water is visible
(C) only rooms that customer or adjuster says were affected
(D) all potentially affected areas
(D) all potentially affected areas
Buckled or damaged particle board should
(A) be dried to a pre-loss condition using desiccant dehumidifiers
(B) be removed and replaced with new material
(C) be dried from underneath the subfloor
(A) remove the excess water
(B) check for moisture in walls
(C) identify and address potential safety hazards
(D) eliminate possible furniture staining and damage
(C) identify and address potential safety hazards
A significant amount of water absorption and evaporation load where wet porous materials
represent ~5% to ~40% of combined ceiling, walls, and flooring surface areas and where low
evaporation materials and assemblies are minimally wet is
(A) class 1
(B) class 2
(C) class 3
(D) class 4
(B) class 2
Multiple extractions of salvageable materials, especially porous material (carpet, cushion),
often are required to
(A) eliminate potential microbial growth
(B) decrease drying time
(C) eliminate the need for antimicrobial (biocide) application
(D) increase the need for additional dehumidification
To enhance drying, restorers should manage both ambient temperature and.
(A) surface temperatures of affected materials
(B)outside temperatures of building envelopes
,(C) dehumidifier process output temperatures
, (D) output temperatures of the airmovers
(A) surface temperature of affected materials
Water damage restoration services should not begin until after the
(A) damage survey has been submitted
(B) restorer has entered into an adequately written contract
(C) insurance adjuster authorizes the work
(D) insurance policy has been reviewed and explained
(B) restorer has entered into an adequately written contract
Two tools that should be used properly disengage most stretched-in carpet are
(A) pliers and staple remover
(B) power stretcher and knee kicker
(C) knee kicker and carpet awl.
(D) base molding lifter and carpet awl
(C) knee kicker and carpet awl
When inspecting a water-damaged structure, restorers should inspect
(A) with thermal imaging camera to show definite areas of water
(B) only where water is visible
(C) only rooms that customer or adjuster says were affected
(D) all potentially affected areas
(D) all potentially affected areas
Buckled or damaged particle board should
(A) be dried to a pre-loss condition using desiccant dehumidifiers
(B) be removed and replaced with new material
(C) be dried from underneath the subfloor
