2T2X1 5 Level CDC Vol. 1 Questions and
Answers Already Passed
What is the primary function of an aircraft armament system?
A) To provide ground support equipment
B) To manage and maintain inventory
✔✔C) To manage and control aircraft weaponry and munitions
D) To service fuel systems
What is used to prevent inadvertent release of ordnance on an aircraft?
✔✔A) Safety pins
B) Hydraulic lines
C) Fire extinguishers
D) Electrical circuits
Which component is responsible for powering the aircraft’s weapons control system?
A) Battery pack
✔✔B) Aircraft electrical system
C) Hydraulic system
1
,D) Oxygen supply system
What should be done if an aircraft ordnance system shows signs of malfunction?
✔✔A) Report it and follow safety procedures
B) Continue normal operation until a scheduled maintenance
C) Replace the malfunctioning component immediately
D) Disable the system
Which of the following is the best practice for storing explosives on an aircraft?
✔✔A) In a well-ventilated, secure, and authorized storage area
B) In any available compartment
C) In the cockpit
D) In the tail section of the aircraft
What is the purpose of the aircraft’s weapons control panel?
✔✔A) To manage the selection, arming, and release of ordnance
B) To monitor fuel levels
C) To control engine speed
2
,D) To adjust wing flaps
How are aircraft ordnance safety devices removed prior to a mission?
✔✔A) By authorized personnel according to safety procedures
B) Automatically by the aircraft's electronic system
C) By the pilot after takeoff
D) After the ordnance is fired
What is the correct procedure for loading bombs onto an aircraft?
✔✔A) Follow the aircraft’s loading manual and safety guidelines
B) Load the bombs without safety checks
C) Load the bombs only when there is an emergency
D) Load bombs after reaching cruising altitude
Which of the following systems is checked to ensure correct operation of the aircraft’s
weaponry?
A) Environmental control system
✔✔B) Aircraft armament control system
3
, C) Flight navigation system
D) Communications system
What is the purpose of aircraft armament control cables?
✔✔A) To transmit signals that control the release of ordnance
B) To provide power to the aircraft engines
C) To regulate cabin temperature
D) To control the aircraft’s speed
When conducting a preflight check, what should be inspected on the aircraft’s ordnance system?
✔✔A) Ensure all safety pins and devices are in place
B) Check the fuel system
C) Verify the navigation equipment
D) Inspect the aircraft’s wingspan
Which of the following best describes the role of the aircraft’s weapons maintenance team?
A) To perform cosmetic repairs
✔✔B) To inspect, maintain, and repair the weapons systems
4
Answers Already Passed
What is the primary function of an aircraft armament system?
A) To provide ground support equipment
B) To manage and maintain inventory
✔✔C) To manage and control aircraft weaponry and munitions
D) To service fuel systems
What is used to prevent inadvertent release of ordnance on an aircraft?
✔✔A) Safety pins
B) Hydraulic lines
C) Fire extinguishers
D) Electrical circuits
Which component is responsible for powering the aircraft’s weapons control system?
A) Battery pack
✔✔B) Aircraft electrical system
C) Hydraulic system
1
,D) Oxygen supply system
What should be done if an aircraft ordnance system shows signs of malfunction?
✔✔A) Report it and follow safety procedures
B) Continue normal operation until a scheduled maintenance
C) Replace the malfunctioning component immediately
D) Disable the system
Which of the following is the best practice for storing explosives on an aircraft?
✔✔A) In a well-ventilated, secure, and authorized storage area
B) In any available compartment
C) In the cockpit
D) In the tail section of the aircraft
What is the purpose of the aircraft’s weapons control panel?
✔✔A) To manage the selection, arming, and release of ordnance
B) To monitor fuel levels
C) To control engine speed
2
,D) To adjust wing flaps
How are aircraft ordnance safety devices removed prior to a mission?
✔✔A) By authorized personnel according to safety procedures
B) Automatically by the aircraft's electronic system
C) By the pilot after takeoff
D) After the ordnance is fired
What is the correct procedure for loading bombs onto an aircraft?
✔✔A) Follow the aircraft’s loading manual and safety guidelines
B) Load the bombs without safety checks
C) Load the bombs only when there is an emergency
D) Load bombs after reaching cruising altitude
Which of the following systems is checked to ensure correct operation of the aircraft’s
weaponry?
A) Environmental control system
✔✔B) Aircraft armament control system
3
, C) Flight navigation system
D) Communications system
What is the purpose of aircraft armament control cables?
✔✔A) To transmit signals that control the release of ordnance
B) To provide power to the aircraft engines
C) To regulate cabin temperature
D) To control the aircraft’s speed
When conducting a preflight check, what should be inspected on the aircraft’s ordnance system?
✔✔A) Ensure all safety pins and devices are in place
B) Check the fuel system
C) Verify the navigation equipment
D) Inspect the aircraft’s wingspan
Which of the following best describes the role of the aircraft’s weapons maintenance team?
A) To perform cosmetic repairs
✔✔B) To inspect, maintain, and repair the weapons systems
4
