©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
Ammo CDC's set B Exam Questions And
Correct Answers
Before using an electric drill, what is the first thing you should do? - answer✔Make sure the
diameter of the hole to be drilled is within the capacity of the drill
The purpose of cutting lubricant in most drilling ops is to increase the - answer✔Drilling speed
and drill bit life
Minimum protection using a bench grinder - answer✔eye and face protection
what condition would prevent an operator from applying power to a hoist or other powered
lifting device - answer✔an AF Form 979
most common type of lifting sling - answer✔wire rope
the enunciators displayed on the fluke 8025 series multimeter are used to distinguish among -
answer✔ohms, kilohm, and megohms
2 operational modes of the Fluke 8025 - answer✔range and hold
the steering system on the MHU 141/ M trailer has a turning radius of how many inches -
answer✔200
When the MHU 141 trailer is loaded or towed with the hinged deck panels open, what must be
done? - answer✔the deck supports must be properly positioned and locked in place with quick
release pins
Max load capacity of the MHU 110/ M trailer - answer✔15,000
the parking brake on the MHU 110/ M is applied by - answer✔pulling either one of two hand
levers located on each side of the front of trailer
how many openings are on the deck of the MHU- 226 trailer - answer✔3
what type of steering aids the MHU- 226 - answer✔four wheeled double ackerman
1|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
After 463L pallets are positioned on a rollerized trailer, what can you use to secure the pallets -
answer✔MB-1 chain assemblies and or tie down straps
what kind of movements supports on base activities to or from the flightline -
answer✔operational
what munitions item is not loaded into transport modules by munitions personnel - answer✔20
mm
what transport module used for decoy munitions has a max capacity of 30 magazines -
answer✔ALE- 50
How often should the positive locking devices on the doors of munitions transport modules be
checked - answer✔after loading, unloading and periodically between stops
the purpose of the transport beam beneath the lift arm assemblies on the MJ- 1 series lift truck
is to - answer✔provide added support and to relieve hydraulic pressure from the lift arms when
carrying loads for long distances
Lifting capacity of the MJ 1 series lift truck - answer✔3,000
Lifting capacity of MHU 83 lift truck - answer✔7,000
When using fork adapters on MHU 83 series lift truck - answer✔it reduces lifting capacity by
1,000
What happens when you release the accelerator pedal on a vehicle driven with a hydrostatic
transmission - answer✔the unit coasts to a stop very quickly
what is the primary drawback to using the hydraulic hand pump to build hydraulic pressure on
the MHU 83 lift truck - answer✔extremely slow way to build hydraulic pressure
How is the yaw positioning from the cradle or boom controls of an MJ 1 lift truck adjusted -
answer✔Manually
what category are Air Force air compressors classified? - answer✔high or low pressure
what is the purpose behind good operator maintenance of all assigned vehicles -
answer✔maintain vehicle serviceability at reduced cost
max amount thee MB 4 aircraft towing tractor can tow - answer✔140,000
pintle safety locking pins must remain attached to the pintle assembly - answer✔to prevent an
insecure pin from coming out and getting lost
what gear should a tractor with automatic transmission while going downhill - answer✔low
2|Page
ALL RIGHTS RESERVED.
Ammo CDC's set B Exam Questions And
Correct Answers
Before using an electric drill, what is the first thing you should do? - answer✔Make sure the
diameter of the hole to be drilled is within the capacity of the drill
The purpose of cutting lubricant in most drilling ops is to increase the - answer✔Drilling speed
and drill bit life
Minimum protection using a bench grinder - answer✔eye and face protection
what condition would prevent an operator from applying power to a hoist or other powered
lifting device - answer✔an AF Form 979
most common type of lifting sling - answer✔wire rope
the enunciators displayed on the fluke 8025 series multimeter are used to distinguish among -
answer✔ohms, kilohm, and megohms
2 operational modes of the Fluke 8025 - answer✔range and hold
the steering system on the MHU 141/ M trailer has a turning radius of how many inches -
answer✔200
When the MHU 141 trailer is loaded or towed with the hinged deck panels open, what must be
done? - answer✔the deck supports must be properly positioned and locked in place with quick
release pins
Max load capacity of the MHU 110/ M trailer - answer✔15,000
the parking brake on the MHU 110/ M is applied by - answer✔pulling either one of two hand
levers located on each side of the front of trailer
how many openings are on the deck of the MHU- 226 trailer - answer✔3
what type of steering aids the MHU- 226 - answer✔four wheeled double ackerman
1|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
After 463L pallets are positioned on a rollerized trailer, what can you use to secure the pallets -
answer✔MB-1 chain assemblies and or tie down straps
what kind of movements supports on base activities to or from the flightline -
answer✔operational
what munitions item is not loaded into transport modules by munitions personnel - answer✔20
mm
what transport module used for decoy munitions has a max capacity of 30 magazines -
answer✔ALE- 50
How often should the positive locking devices on the doors of munitions transport modules be
checked - answer✔after loading, unloading and periodically between stops
the purpose of the transport beam beneath the lift arm assemblies on the MJ- 1 series lift truck
is to - answer✔provide added support and to relieve hydraulic pressure from the lift arms when
carrying loads for long distances
Lifting capacity of the MJ 1 series lift truck - answer✔3,000
Lifting capacity of MHU 83 lift truck - answer✔7,000
When using fork adapters on MHU 83 series lift truck - answer✔it reduces lifting capacity by
1,000
What happens when you release the accelerator pedal on a vehicle driven with a hydrostatic
transmission - answer✔the unit coasts to a stop very quickly
what is the primary drawback to using the hydraulic hand pump to build hydraulic pressure on
the MHU 83 lift truck - answer✔extremely slow way to build hydraulic pressure
How is the yaw positioning from the cradle or boom controls of an MJ 1 lift truck adjusted -
answer✔Manually
what category are Air Force air compressors classified? - answer✔high or low pressure
what is the purpose behind good operator maintenance of all assigned vehicles -
answer✔maintain vehicle serviceability at reduced cost
max amount thee MB 4 aircraft towing tractor can tow - answer✔140,000
pintle safety locking pins must remain attached to the pintle assembly - answer✔to prevent an
insecure pin from coming out and getting lost
what gear should a tractor with automatic transmission while going downhill - answer✔low
2|Page
